Guarantee - JP Selecta EMPLOW-S Manual De Instrucciones

MANUAL DE INSTRUCCIONES
J
.P. SELECTA s.a.u.
CODIGO 80115 REV E FEB 2017
- Unscrew the securing screw on the bottom right turn hinge.
- Open the door.
- Hold the door on the handle side and at the bottom and lift it.
- The bearing pin (21) should come out of the turn hinge (2).
- If the bearing pin (21) does not come out, press the pin out from underneath.
- Swing door out at the bottom and remove it.
- Unscrew the turn hinge (2).
- Unscrew the bearing element, (3) transfer it to the opposite location hole
of the turn hinge and screw it fi rmly into place.
- Take the stopper (4) out of the turn hinge and transfer it to the receiving
hole on the opposite side of the turn hinge.
- Carefully lift off the cover (5) on the handle side.
- Undo the screw (6) and transfer it to the opposite side.
- Put the cover (5) back on.
- Screw the turn hinge (2) fi rmly into place on the new hinge side (with 4 Nm),
possibly using a power screwdriver.
- At the top, use a screwdriver to unclip cover (7) and cover (8) at the front,
and remove by pulling out and down.
- Unscrew the bearing pin (9) and screw it fi rmly into place on the opposite
side (with 4 Nm).
- Refi t the cover (7) on the side of the bearing pin: insert at the back, snap
in at the front.
- Fit the cover (8) on the opposite side: insert at the back, snap in at the front.
- Lift the stopper (12) out of the door bearing bush and transfer it.
- Detach door handle, stoppers (10) and pressure plates (11) and transfer to
the opposite side.
- When mounting the pressure plates, make sure they snap into place properly.
- Transfer the spring clamp (20): Depress the latch nose and pull the spring
clamp off over it.
- Slide the spring clamp into place on the new hinge side until it clicks into place.
- Pull the bearing pin (21) out of the door bush and transfer it to the opposite
side together with the washer. The latch nose must point to the inner side
of the door, the notch to the outer side.
- Hang the door on the bearing pin (9) at the top.
- Swing the door in at the bottom and insert the bearing pin (21) into the turn
hinge. If necessary, turn the bearing pin until it snaps into place.
- Insert the securing screw (1) at the bottom into the bearing pin and tighten
it (with 4 Nm).
- If necessary, align the door fl ush with the appliance housing using the two
slots in the turn hinge. To do so, unscrew the middle screw.
WARNING
Risk of injury due to the door dropping out!
If the bearing parts are not screwed into place fi rmly enough, the door may
drop out. This may lead to severe injuries. What is more, the door may not
close and therefore the appliance may fail to cool properly.
- Screw on the bearing brackets/bearing pins tightly (4 Nm).
- Check all of the screws and retighten if necessary.

10 Guarantee

This product is guaranteed for one year. The guarantee does not cover damages
caused by an incorrect use or causes beyond the control of J.P. SELECTA, s.a.u.
Any manipulation of the equipment by personnel not authorized by J.P. SELECTA,
s.a.u. automatically cancels the guarantee.
Ctra. NII Km 585.1 Abrera 08630 (Barcelona) España
e-mail: selecta @jpselecta.es - website: http://www.jpselecta.es
(Sujetas a modifi caciones sin previo aviso)
Tel 34 937 700 877 Fax 34 937 702 362
Pag.: 20