Track Selection; Pitch Bend - Gemini CDM-3250 Manual De Instrucciones

BEND mode the JOG WHEEL will function the same as the
PITCH BEND allowing you to speed up (FORWARD) or slow
down (REWIND) the music clockwise being (FORWARD) and
counter clockwise being (REWIND).
11 JOG MODE BUTTON: When the JOG MODE BUTTON is il-
luminated it indicates the JOG WHEEL is in SEARCH MODE,
and when not illuminated it indicates that the JOG WHEEL is in
PITCH BEND MODE.
12
DISPLAY: The DISPLAY shows the track number, pitch value,
pitch bend, single, continue (for continuous play), play/pause
modes, fast forward/reverse modes, loop mode, reloop mode,
PGM, repeat modes, the playback display bar, and three differ-
ent time displays. These times displays are TIME ELAPSED on
the track, TIME REMAINING on the disc and TIME REMAIN-
ING on the track. Time is measured in minutes, seconds and
frames.
13 PGM: Allows you to create a set playlist. To program a set list
into the CDM-3250 memory, begin by stopping the unit from
play and pressing PGM to begin the set list. Select a track by
using the track selection button to scan to the first track to be
placed in the set list. When you have selected the proper track
press PGM and the CDM-3250 will be ready to set your next
selection. Repeat the previous steps until you have completed
your play list, then press play to begin the set list.
14 SINGLE: Pressing the SINGLE button engages SINGLE mode,
in this mode the CDM-3250 will play one song and then stop.
Pressing the SINGLE button again will then activate CONTINU-
OUS mode causing the unit to play continuously (after the last
track, the unit will return to the first track of the disc and con-
tinue to play).
TIME: The TIME button switches the time display between
15
three available sources, these three are TIME ELAPSED on the
track, TOTAL REMAIN on the disc and REMAIN on the track.
TIME ELAPSED indicates how much time has currently gone
by since the play button was pressed, TOTAL REMAIN will
count down the time remaining on the entire disc and REMAIN
counts down the time that is left before the end of the track.
PITCH: Hold the PITCH button to activate the PITCH CON-
16
TROL SLIDE. Pitch ranges can be controlled through the use
of the PITCH CONTROL SLIDER. Hold the PITCH button again
to deactivate this mode.
PITCH CONTROL SLIDE: Moving the PITCH CONTROL SLIDE
17
up or down will change the pitch percentage +/ - 12%.
PITCH BEND: Pushing the PITCH BEND BUTTONS will auto-
18
matically raise the pitch up to +16% or lower the pitch down
to -16% from the existing pitch setting. Releasing the buttons
will return the pitch to the original pitch setting. You can use
this function to match the beat when mixing from one song to
another.
LOOP SECTION: A LOOP repeats the section between the entry
19
point (IN) and the exit point (OUT).
A. To set a loop while the unit is playing, start by pressing the
IN BUTTON (it will light up)
B. When you reach the desired end loop point press the OUT
BUTTON (it will also light up). The loop will continue playing
until you press the OUT BUTTON again allowing the music to
continue from that point on.
C. To re-engage the loop you must press the RELOOP BUT-
TON.
D. When you have released your loop the OUT BUTTON will
turn OFF and the IN BUTTON will remain lit to indicate that
your loop is stored in the CDM-3250 memory.
E. Pressing the IN BUTTON again while the unit is playing will
erase the previously saved loop while saving your new loop
entry point.
F. Press OUT to exit the loop and save a new complete loop.
G. Press RELOOP to return to the beginning of the previously
saved loop from normal play. Press RELOOP repeatedly to
cause the loop to stutter.
NOTE: THE FIRST LOOP WILL HAVE A PAUSE AT THE EXIT
POINT, WHILE ALL OTHERS WILL BE SEAMLESS.
20
PLAY / PAUSE: Each press of the PLAY / PAUSE BUTTON
causes the operation to change from PLAY to PAUSE or from
PAUSE back to PLAY. The PLAY/PAUSE BUTTON remains lit
when in PLAY mode, while it blinks in PAUSE mode.
21
CUE: While the unit is playing and after the cue point has been
programmed, pressing CUE will cause the CD player to enter
the PAUSE mode (PLAY/PAUSE BUTTON blinks) at the pro-
grammed cue point (the CUE LED is lit). Holding down the CUE
button changes the function to preview, and allows you to stutter
start or play from the programmed CUE POINT. Releasing the
CUE button will return the CD to the preset CUE point.
22
TRACK SELECTION: The TRACK SELECTION buttons let you
select the track to play. +10 allows you to scan through the track
selection in increments of 10. TRACK SKIP allows you to scan
through each track one at a time. Select the track desired by
pressing the TRACK SELECTION BUTTON.
NOTE: ONCE YOU HAVE SKIPPED TO ANOTHER TRACK, YOU
MAY NOT GO BACK TO YOUR PROGRAMMED CUE POINT.
YOU MUST BEGIN YOUR CUE SELECTION OVER AGAIN, THE
CUE WILL BE PRESET TO THE BEGIN-NING OF THE NEWLY
SELECTED TRACK.
CDM-3250
5