stayer CP L20 Manual De Instrucciones página 17

Starting Operation
Switching On and Off
To start the machine, first push the lock-off button for the
On/Off switch 2 and then press the On/Off switch 1 and
keep it pressed.
To switch off the machine, release the On/Off switch 1.
Note: For safety reasons, the On/Off switch 1 cannot be
locked; it must remain pressed during the entire operation.
To save energy, only switch the power tool on when using it.
Working Advice
Protect saw blades against impact and shock.
Guide the machine evenly and with light feed in the cutting
direction.
Excessive feed significantly reduces the service life of
the saw blade and can cause damage to the power tool.
Sawing performance and cutting quality depend essentially
on the condition and the tooth form of the saw blade.
Therefore, use only sharp saw blades that are suited for
the material to be worked.
- Before any work on the machine itself, disconnect
the battery.
Sawing Wood
The correct selection of the saw blade depends on the
type and quality of the wood and whether lengthway or
crossway cuts are required.
When cutting spruce lengthways, long spiral chips are
formed.
Beech and oak dusts are especially detrimental to health.
Therefore, work only with dust extraction.
Sawing with Parallel Guide
The parallel guide 10 enables exact cuts along a workpiece
edge and cutting strips of the same dimension.
Loosen wing bolt 7 and slide the scale of the parallel
guide 10 through the guide in the base plate 12. Adjust the
desired cutting width as the scale setting at the respective
cutting mark 9 or 8; see Section "Cutting Marks". Tighten
wing bolt 7 again.
Sawing with Auxiliary Guide
For sawing large workpieces or straight edges, a board or
strip can be clamped to the workpiece as an auxiliary
guide; the base plate of the circular saw can be guided
alongside the auxiliary guide.
Repair service
Our after-sales service responds to your questions
conceming maintenance and repair ofyour product as well
as spare parts.
Exploded views and information on spare parts can also
be found under: info@grupostayer.com
Our customer consultants answer your questions
conceming best buy, application and adjustment of
productsand accessories.
Warranty
Warranty card
lncluded in the documentation that accompanies this
equipment, you should find the warranty card. You should
fill out the card completely and retum to vendar with a copy
of purchasing receipt or invoice and you should receive a
ENGLISH
17
receipt.
Note: lf you cannot find the warranty card within
the documentation,youmust ask for it through your
supplier.
The warranty is limited only to manufacturing defects and
expire if pieces have been removed or manipulated or
repaired otherthan themanufacturer.
Environment
The machine, accessories and packaging should be
sorted for environmental-friendly recycling.
OnlyforEC countries:
Do not dispose of power tools into household waste!
According the European Guideline 2002/96/
EC for Waste Electrical and Electronic
Equipment and its implementation into national
right,power tools that are no longer usable
must be collected separately and disposed of
in an environmentally correct manner.
Subject to change wlthout notlce.
Declaration of conformity
The undersigned: STAYER IBERICA, S.A.
With address at:
Calle Sierra de Cazorla, 7
Área Empresarial Andalucía - Sector 1
28320 PINTO (MADRID)
Tel.:+34 91 691 86 30 / Fax: +34 91 691 86 31
CERTIFIES
That the machine:
CIRCULAR SAW
Type:
I declare under our responsibility that the product
described under "Technical Data" is in accordance with
the following standards or standardized documents: EN
60745-1, EN 60745-2-5, according to regulations 2011/65/
UE, 2004/108/CE, 2014/30/UE, 2006/42/CE.
Ramiro de la fuente
Managing Director
17
January 5, 2019