Publicidad
Idiomas disponibles
Idiomas disponibles
Liquno
iCanto MS1 Bluetooth Speaker
Device Layout
Specifications
USB Charging input voltage: 5V @
✓
500MA
Speaker Specifications:
✓
Φ 40mm unit / 4 ohms / 3.5W
o
bandwidth 90 Hz -20 kHz
o
sensitivity: 85dB
o
Maximum speaker rated power
✓
output: 3W
Lithium battery:
✓
capacity 3.7V/280MA
o
maximum play time:
o
approximately 2 hours (Vary
with volume)
fully charge time: approximately
o
2 hours
Charge Voltage/Current: 5V
o
+0.25V/1A
✓
Maximum Power Distortion: 7%
Signal-to-noise ratio: 90 hZ @
✓
20K/65dB
1.
Power ON/OFF
2.
Speaker
3.
Previous / Volume-
4.
Microphone
5.
Next / Volume +
6.
Charging port
7.
LED indicator
8.
Suction Cup
9.
USB Cable
Bluetooth version: 5.0
✓
SBC \ MP3 \AAC audio decoding
✓
function
Compatible A2DP\AVRCP high-
✓
quality stereo audio transmission
with long-range control
Supports Bluetooth hands-free
✓
function.
Microphone sensitivity: -32dB
✓
Embedded DSP data processor
✓
Noise cancellation support
✓
Bluetooth:
✓
Frequency band: 2.4GHz ISM,
o
Frequency response: 2.402
o
GHz - 2.480 GHz
the effective transmission
o
distance up to within 10
meters
Operating Temperature: -10 - +40
✓
degrees Celsius
Product size: 60*60*60mm
✓
Operating Instructions
1. After 2 seconds continued pressing
button, voice notice and LED flashes
blue. Your speaker is now ready to
connect to your sound playing device,
and should be connected to the
Bluetooth device with the name "BT-
280"
2. After enabling Bluetooth function in the
Bluetooth device, scan for the available
Bluetooth devices and select "BT-280"
from the list available, Voila!
3. The last connected device will be stored
in memory and by rebooting the
speaker by a short press of the
button every time, the speaker will
connect to the last successful paired
device automatically.
Please note:
If the pairing is unsuccessful, please turn
off the speaker first, then turn on and try
connecting again. Also disconnect the
speaker from any other playing device,
see instructions below.
Connecting speaker to another device
When the device is connected to a
Bluetooth playing audio device, and if it
needs to be connected to another
Bluetooth audio device, please remove
the Bluetooth from the current connected
device, and restart the speaker by setting
it to the [Off] mode. After disconnecting,
you can start the procedure above
'Booting the speaker and Bluetooth
paring' for a new pairing.
ENGLISH
Speaker Functions
POWER ON/OFF -
Long press for 3
seconds
- Power ON (Blue light starts Blinking)
- Power OFF (Blue light turns off)
When the Bluetooth Mode is on, Press
for
- Play/Pause/Answer/End/Cancel Dial
Next Song/Volume UP
• While playing music, shortly press the
key and it the speaker will play the next
song in your music list. Hold the
button for longer for Volume
Increase.
Previous Song/Volume Down
• While playing music, shortly press the
key and the music will go back to the
previous song. Hold the button for
longer for Volume Decrease.
Important notes
•
This product is not a toy.
•
Do not drop or damage the
speaker.
•
Do not use in humid or extreme
temperatures.
•
Do not place the speaker near an
open flame.
•
Do not block the sound of the
speaker while it is in use.
•
Do not use the unit if it has been
dropped or damaged in any way.
•
If damaged, do not attempt to
repair or disassemble the speaker.
Publicidad
