Moeblelplus 3LIK0610 Manual De Utilización página 22

Commands: (Fig.11)
Push-button A = on/off lights switch
Push-button B = on/off cooker hood switch. The appliance
switches on at speed level 1, If the cooker hood is on depress
the push-button for 2 sec. to switch off the cooker hood. If
the cooker hood is at speed level 1 it will not be necessary
to depress the push-button to switch the cooker hood off .
Decreases the motor speed.
Display C = indicates the motor speed level selected and
activates the timer.
Push-button D = switches on the cooker hood. Increases the
motor speed. Touching the key at 3rd speed, the intensive
function runs for 10' , then the appliance go back to work at the
original speed. During this function the display blinks.
Key E = The Timer times the functions on activation for
15 minutes, after which they are switched off . The Timer is
deactivated by re-pressing Key E. When the Timer is activated
the decimal point must fl ash on the display. The Timer cannot
be activated if the intensive speed is functioning.
The "clean air" function is activated by pressing key E for 2
seconds when the appliance is switched off . This switches
the motor on for 10 minutes every hour at the fi rst speed.
During functioning a rotary movement of the peripheral
segments must be visualised on the display. When this time
has passed the motor switches off and the fi xed letter "C" must
be visualised on the display until the motor re-starts after 50
minutes for another 10 minutes and so on. Press any key apart
from the light keys to return to normal functioning. Press key
E to deactivate the function.
• Active carbon/grease fi lter saturation:
- When display item C fl ashes, at a speed where it alternates
with the letter F (e.g. 1 and F), the grease fi lters must be
washed.
- When display item C fl ashes, at a speed where it alternates
with the letter A (e.g. 1 and A), the carbon fi lters must be
replaced.
After the clean filter has been positioned correctly, the
electronic memory must be reset by pressing button A
for approximately 5 seconds, until the indication F or
t shown on the display C stops fl ashing.
• Commands: (Fig.12A-12B)
NOTE: With this control it is possible to manage the appliance
also with a remote control to be requested as accessory.
Power Button (A) = the on / off button switches on and off
the whole hood (motor and lights).
By pressing the button the motor starts at 1st speed.
Fan Speed button (B) = From the OFF position, press once
for the 1st speed, twice for the 2nd speed and three times
for the 3rd speed. In order to activate the intensive speed,
press the button for 5 seconds regardless of the status of the
hood. For each speed only the led indicating the set speed
will turn on. The intensive speed is indicated by the fl ashing
of the led indicating speed 3. The duration of the intensive
speed is 10 minutes; after this time the hood goes back to
the last set speed.
In order to remove the intensive speed press the power button
and the hood will switch off , or press the Fan speed button
and the speed goes back to the previously set one. Speed of
the hood with cyclic trend.
Light button (C)= There are three light levels: High, medium,
low.
From the off position press once for the high level, twice for
the medium level, three times for the low level and four times
to turn the lights off .
The level of the lights has a cyclic trend: High, medium,
low, off .
Timer button (D) = With any type of speed (excluding the
intensive speed), by pressing the button, the timer function
is activated for 15 minutes. After this time has elapsed the
hood will turn off (motor and any light on).
Lights indicator (E) = The lights indicator will switch on when
the lights are on at any level.
Filters indicator (F) = After 30 minutes of operation, the led
of the fi lters indicator will switch on, not fl ashing indicating
that the anti-grease fi lters have to be washed. To reset the
function (with the hood off ), press the Fan speed button for
5 seconds. After this operation, the led of the fi lters indicator
turns off and the setting of the 30 hours starts again from
the beginning.
After 120 hours the led will fl ash continuously. This means
that the carbon fi lters have to be replaced (if present). To reset
the function (with hood off ) press the Fan speed button for 5
seconds. After this operation, the led of the indicator turns off
and the setting starts again from the beginning
Clean air indicator (8).
With the hood off , press the Power button (1) for 5 seconds to
activate the clean air function. This will switch on the motor
at speed 1 for 10 minutes every hour. The light indicator will
switch on without fl ashing and the led of the 1st speed will
switch on. In the remaining 50 minutes the light indicator will
fl ash. The function can be deactivated by pressing any button
except for the lights one.
THE MANUFACTURER DECLINES ALL RESPONSIBILITY FOR
EVENTUAL DAMAGES CAUSED BY BREACHING THE ABOVE
WARNINGS.
- 22 -