Mamas & Papas Vito Manual Del Usuario página 24

Isofix attachments are extended to their maximum length.
1 0• Remove the protective base attached to the car seat with
the special release switches (Arrows A and B).
1 1• Position the car seat on the Isofix Base 0+1 and secure the
rear connectors of the car seat to the attachment points
of the base nearest to the vehicle seat (Arrow A). Press the
front part of the car seat until it clicks into place (Arrow B).
1 2• IMPORTANT: The two signals behind the Isofix Base go
from red to green to indicate that the car seat is properly
attached to the base.
1 3• Pull the handle on the base (Arrow A) and push the base
with the car seat against the vehicle's seat until they can
go no further (Arrow B).
IMPORTANT: It is possible to check that the Isofix base
is correctly positioned by looking at the signals on the
handle. OK (green) indicates that the position is correct,
NO (red) indicates that the procedure has been carried out
incorrectly and must be repeated until the handle only
shows the term "OK".
IMPORTANT: Once the procedure is complete, move
the base to check that both Isofix points are actually
attached.
How to put the child in the Vito car seat
1 4• Before sitting the child on the stroller, release the safety
harness by pushing the red button in the buckle of the leg
divider strap.
15• Lift the safety harness and attach the buckles to the elastics
in the sides.
16• Sit the child in the stroller and adjust the safety straps
round the child's shoulders and waist, as shown in the
picture.
17• Fasten the harness by overlapping the two straps and
inserting the buckles into the leg divider strap until they
click into place.
18• The child is sitting correctly with the safety harness
fastened properly.
19• To tighten the strap, pull the central adjusting strap
towards you as shown in the picture. The straps will
tighten round the child. Be careful not to pull too much.
IMPORTANT: Do not tighten too much (the harness
All manuals and user guides at all-guides.com
should be loose enough for you to slip a finger
between the strap and the child's chest).
20• To loosen the safety straps, push the button in the middle of
the car seat and at the same time pull the straps towards you.
IMPORTANT: Grab hold of the safety harness under
the shoulder pads, as shown in the picture.
• The seat has a booster cushion which is suitable for small
babies and when the safety harnesses are in the first level.
When the child is older, remove the booster cushion.
2 1• To remove the booster cushion, pull it out of the safety
harness and the sides of the car seat.
How to adjust the height of the head rest
The head rest must be adjusted to match the child's
height. There are 7 positions.
22• To change from a lower position to a higher one:
pull the strap in the upper central part of the headrest
upwards. The headrest will move at the same time.
To change from a higher position to a lower one:
pull the strap in the upper central part of the headrest
upwards and, at the same time, push the headrest down to
the desired position.
When you have finished, try moving the headrest to
check it is properly attached.
2 3• When the straps are positioned correctly, the child's
shoulders will be just below the point where the straps pass.
2 4• IMPORTANT: The straps must not be too high or too
low with respect to the child's shoulders.
2 5• The Vito car seat can be inclined in 4 different positions,
both when it is attached to the base and when it is
attached to the Isofix Base 0+1. To incline the car seat,
press the lever underneath (fig. a) and pull it towards you
into the required position (fig. b).
• To release the Vito car seat from the Isofix Base 0+1, press the
same lever in the same way (See Point 10).
How to remove the lining
To remove the lining of the Vito car seat:
• slip the booster cushion off if there is one (point 21);
• unfasten the safety harness (point14);
2 6• unfasten the straps from the back attachment point;
20