Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
π
H-9304
INDUSTRIAL
GLUE GUN
Nozzle
1.
Fasten output control adjuster.
2. Plug in to a 110 volt outlet.
3. Turn ON/OFF switch on. Red light means power is on.
4. Insert glue stick into back of gun.
5. Allow 3-5 minutes to warm up gun and glue stick.
6. Pull trigger several times until glue is set firmly into
the inlet tube.
7. Apply appropriate amount of glue by squeezing
trigger.
8. The output volume of glue can be adjusted by
turning the output control adjuster. Turn clockwise for
less glue and counterclockwise for more.
9. Bond surfaces by pressing together within 15-20
seconds after applying hot glue. For best results,
surfaces should be clean of any oil and dirt.
PAGE 1 OF 6
1-800-295-5510
uline.com
Wire
Support Stand
OPERATION
Output Control
Adjuster
Trigger
10. Always use the provided wire support stand between
uses when gun is plugged in.
11. Never lay gun on its side while it is still hot.
12. After use, always switch gun to off, unplug gun and
use provided wire support until gun has cooled
before storing.
13. Never pull glue sticks out of gun.
14. If glue drips excessively, replace the nozzle. To
change, heat the gun for a minute until glue is
softened enough to remove the nozzle. While
wearing gloves, use a wrench to remove the old
nozzle. Flush glue through the gun and attach the
new nozzle.
Para Español, vea páginas 3-4.
Pour le français, consulter les pages 5-6.
ON/OFF Switch
0121 IH-9304
Publicidad
Manuales relacionados para Uline H-9304
Resumen de contenidos para Uline H-9304
- Página 1 Para Español, vea páginas 3-4. Pour le français, consulter les pages 5-6. π H-9304 1-800-295-5510 uline.com INDUSTRIAL GLUE GUN Output Control Adjuster Nozzle ON/OFF Switch Trigger Wire Support Stand OPERATION Fasten output control adjuster. 10. Always use the provided wire support stand between uses when gun is plugged in.
- Página 2 • Never use this gun with materials other than • Hot melt glue is not intended to replace structural recommended glue sticks. fasteners or for use when area temperatures reach over 140°F. 1-800-295-5510 uline.com PAGE 2 OF 6 0121 IH-9304...
-
Página 3: Funcionamiento
π H-9304 800-295-5510 uline.mx PISTOLA DE SILICÓN INDUSTRIAL Control de Ajuste de Salida Boquilla Interruptor de Encendido/Apagado Gatillo Soporte de Alambre FUNCIONAMIENTO Inserte el control de ajuste de salida. 10. Mientras está enchufada y entre cada uso, utilice siempre el soporte de la pistola. - Página 4 • No use nunca esta pistola con materiales que no usarse en áreas a una temperatura superior a los sean las barras de silicón recomendadas. 60°C (140°F). 800-295-5510 uline.mx PAGE 4 OF 6 0121 IH-9304...
- Página 5 π H-9304 1-800-295-5510 uline.ca PISTOLET À COLLE INDUSTRIEL Dispositif de réglage du débit Buse Interrupteur marche/arrêt Détente Support en métal FONCTIONNEMENT Fixez le dispositif de réglage du débit. 10. Lorsque le pistolet est branché, utilisez toujours le support en métal fourni entre les utilisations.
- Página 6 • N'utilisez jamais ce pistolet avec des matériaux • La colle thermofusible ne doit pas être utilisée pour autres que les bâtons de colle recommandés. remplacer les fixations structurelles ou lorsque la température ambiante atteint plus de 60 °C (140 °F). 1-800-295-5510 uline.ca PAGE 6 OF 6 0121 IH-9304...