All manuals and user guides at all-guides.com
Stopwatch <SP>
Press
to select Lap (LA) or Split (SP) mode.
Under LA mode:
• Press
to start counting.
• Press
to display the first read-out.
• The stopwatch resets to zero and restarts counting internally.
• Press
to display the counting.
• Press
again to display the second read-out.
• The stopwatch resets to zero and restarts counting internally.
• Repeat the above steps as desired.
• Press
to stop counting.
• Press
to reset the stopwatch to zero.
Under SP mode:
• Press
to start counting.
• Press
to display the first read-out.
• As the stopwatch continues counting internally:
• Press
to mark time.
• Press
to pause and display the marked read-out.
• Repeat the above steps as desired.
alternatively:
• Press
to continue counting.
• Press
to pause and display the read-out.
• Repeat the above steps as desired.
• Press
to stop counting.
• Press
to reset the stopwatch to zero.
9
Radio-controlled time reception information <RI>
Shows information relevant to the last successful reception. This includes
the local time at which the last successful synchronisation takes place.
Last reception time
Length of last reception
Radio Signal Reception
When in reception mode, the radio tower icon
display. The wave indicator
shows the strength of reception.
The range is from 0 - 6 bars. 0 is the weakest and 6 is the strongest.
Both auto and manual reception is possible. Each reception session lasts
15 minutes at maximum. Auto reception takes place twice daily at
1:05 am and 3:05 am. Manual reception is activated by pressing and
holding
until the radio tower icon is shown. To cancel reception,
press and hold
until the icon disappears.
11
Radio-controlled time reception <RX>
To activate the reception:
• Press SET button.
• Press
or
SEL -- selected single band (WWVB, DCF, MSF, JJY40 or JJY60)
DUAL -- Japan dual band scanning (JJY40 and JJY60)
SCAN -- Multi-country scanning (all available bands).
Radio
source
Frequency
Reception
radius
Symbol
• Press SET button to confirm setting.
• The relevant map will stop flashing and stay on display. The radio
tower icon
• If synchronisation is successful, it will override any manually set time.
• If auto synchronisation is not successful, you may set the time manually.
To disable the reception:
• Press SET button to disable the reception.
• The radio tower icon will disappear from the display.
Interference
Reception can be affected by a number of factors. For optimal reception,
please note that:
• A minimum distance of 8 feet should be kept from any interference
source, such as TV sets, computer monitors, microwave ovens and etc.
• Reception might be weak within concrete rooms (e.g. basements,
superstructures, office buildings). In extreme cases, place the clock
close to a window.
• Some localities may be subject to severe atmospheric disturbances.
However, such interference usually weakens during the night.
A single daily reception is sufficient to keep the accuracy reading.
• If the alarm goes off during radio reception, the session will be
interrupted and restart after the alarm has stopped.
will appear on the main
In the event that radio-controlled time reception is not possible,
you may set the time manually.
Manual Time Setting
If you choose to disable the reception for a certain period, or auto
synchronisation is not successful or there is faulty reception, then follow
the steps below to set the clock manually:
In the main display mode:
• Press SET button until the display flashes.
• Press and hold
• Press MODE button once.
• Press and hold
• Press MODE button once.
• Press
or
• Press SET button to confirm setting.
to choose among different reception modes:
WWVB
DCF
MSF
JJY40
Colorado,
Frankfurt,
Rugby,
Fukushima-
USA
Germany
England
East, Japan
60kHz
77.5kHz
60kHz
40kHz
1,500km
1,500km
1,500km
1,500km
will keep flashing until the synchronisation is completed.
10
or
to set the minute and hour.
or
to set the date, month and year.
to set the 12H/24H time display mode.
12
JJY60
Kyushu-
West, Japan
60kHz
1,500km