Perles HSW4186 Instrucciones página 16

The number of revolutions on a grinding or
cutting disc must equal or be higher than the
number of revolutions stated on the tool's
nameplate.
x Grinding and cutting discs should be handled with
care and according to manufacturer's instructions.
x Do not use cutting discs for grinding.
x Grinding accessory must be mounted correctly and it
must rotate freely.
Rotating parts do not stop immediately after
the tool is switched off!
x Do not stop the rotating parts by force.
!
Observe the instruction for the position of the
operator during work, Figure
Always hold the tool in such manner that
sparkles are directed away from the body.
Sparkles can cause fire therefore do not keep
inflammable substances in your vicinity.
x If there is a jam, stop the machine immediately and
unplug it from the mains. Do not start work again until
you have removed the cause of the jam; if it is caused
by the machine itself, please send it to an approved
technical service.
x Do not apply extra pressure on the tool, when it has
already reached its limit operating power. Such use
can damage the tool. If you notice that the tool does
not operate correctly, take it immediately to the
nearest authorized service centre.
Never press the spindle lock-off button when
the motor is running!
Do not put your hands near the rotating
grinding disc.
Switch off the tool after the work is finished
and wait that the rotating parts come to a
complete standstill.
x Always use personal protection equipment such as
protective goggles, gloves, safety footwear, protective
apron and protective mask.
Persons under 16 must not use the tool.
x Use the tool only for dry grinding or cutting.
x Do not work on materials containing asbestos.
x Follow the manufacturer's assembly instructions. Use
only original parts and accessories.
x Always use the tool with its auxiliary handle when you
work with it. Turn the guard corresponding to the
auxiliary handle.
Never use the tool for works above your head.
Do not cut small pieces that cannot be
clamped!
Do not perform work if there could be hidden
installations that could be damaged:
- Water pipes – material damage or electric
shock can be caused!
- Electricity – fire or electric shock can be
caused!
- Gas lines – an explosion can be caused!
All manuals and user guides at all-guides.com
.
18
RISKS AT WORK WITH THE
TOOL
If you observe the enclosed safety instructions
and general safety instructions, you reduce
the risk of unwanted accidents at work.
If you do not check whether the plug is
disconnected from
performing any work on the tool, you increase the
risk of personal injury when putting down the tool
and at sudden connection of power supply.
Use only undamaged three-wire sockets for power
supply.
If you use damaged extension cable or one that is
not made according to current standards that
ensure safety at work outdoors, you are exposed
to the risk of personal injury.
If the supply cord and extension cable are
interwoven, you can trip over the cables, the cable
could be damaged while working with the tool on
the workpiece.
x If after finished work you do not wait till the rotating
parts come to a complete standstill, sudden recoils
can happen when putting down the tool and thereby
cause personal injuries or damage the tool.
x If you try to stop the grinder by force after it had been
switched off, the tool can be destroyed or you can
cause personal injuries.
x If you do not use the auxiliary handle during operation,
you will not be able to guide the tool well and you
could cause injuries
x If you do not observe the instruction for the position of
the operator while working with the tool, you increase
the risk of personal injuries.
In case the tool is jammed and if you do not
immediately switch it off and unplug it, the tool
could recoil at sudden start and cause personal
injuries or it could be damaged.
x If you apply extra pressure on the tool, when it has
already reached its operating power limit, you can
damage the tool.
x If you put your hands too close to the grinding disc,
you can injure your hands.
x If you work on too small pieces that are not well
clamped, you increase the risk of bodily injuries.
x If you do not use personal protection equipment at
work, you can injure your hearing, breathing channels,
eyes and other parts of the body.
x If the tool is used by children or persons that have not
read these operating instructions carefully, there is a
big risk of personal injuries at work or damaging the
tool.
x If you use the tool in an explosive atmosphere,
sparkles could cause an explosion.
x If there is the possibility of exposing the tool to rain,
you risk electric shock, workpiece can get wet and all
personal injuries described before can occur.
If the number of allowed revolutions on a grinding
disc is lower than the number of revolutions on the
grinder's nameplate, the grinding disc can break
and thereby cause serious bodily injuries.
power supply before