Initial Setting; Initial Setup; Main Menu; Tv Functions - Emerson LD195EM8 7 Manual Del Propietário

I
NITIAL SETTING
These operations are accessible by remote control. Some may also be accessible by controls on the main unit.

Initial Setup

This section will guide you through the unit's initial setting which includes
selecting a language for your on-screen menu and auto channel scan,
which automatically scans and memorizes viewable channels.
Before you begin:
Make sure if the unit is connected to antenna or cables.
1
After making all the necessary connections,
press [POWER] to turn on the unit.
• This operation may take a few moments.
2
Use [Cursor K / L ] to select the on-screen language
from the choices on the right side of the TV screen.
(ENGLISH / ESPAÑOL / FRANÇAIS)
or
• "INITIAL SETUP" menu on step 3 will be displayed in
the selected language after you press [ENTER].
3
Use [Cursor K / L ] to select "AUTO PRESET CH(TV/DTV)"
for TV channels or "AUTO PRESET CH(CATV)" for CATV
channels, then press [ENTER].
or
• Scanning and memorizing of channels start
automatically.
• When the scanning and memorizing of channels are
completed, the lowest memorized channel will be
displayed.
All manuals and user guides at all-guides.com

TV Functions

SELECT LANGUAGE
ENGLISH
SELECCIONE EL IDIOMA
ESPAÑOL
CHOISIR LA LANGUE FRANÇAIS
SELECT : K , , L SET : ENTER
SELECCIONE : K , , L AJUSTE : ENTER
CHOIX : K , , L VALIDER : ENTER
- INITIAL SETUP -
PLEASE CONNECT ANTENNA OR CABLE
OR SATELLITE TO THIS UNIT.
AUTO PRESET CH (TV/DTV)
AUTO PRESET CH (CATV)
25
AUTO PRESET CH(TV/DTV)
Note:
• If you connect the cable system directly, contact the CATV
installer.
• If you press [POWER] or [SETUP] during auto channel scan,
this setting will be canceled.
• The initial auto channel scan function can be executed for
either TV/DTV or CATV only once. If you want to scan both
TV/DTV and CATV, you need to select "CHANNEL SETUP" in
the main menu to scan and memorize other channels after
initial presetting is completed. (Refer to page 14.)
• You can cancel or exit the initial auto channel scan menu by
pressing [SETUP].
• When no channel can be received by auto channel scan,
"NO TV SIGNALS" is displayed on the TV screen.
• If there is no signal input from the antenna terminal and
no operation for several seconds after you turn on the unit,
"HELPFUL HINTS" appears. Follow the instructions listed on
the TV screen.
1. PLEASE CHECK TO SEE IF THE
ANTENNA / CABLE / SATELLITE IS
PROPERLY CONNECTED.
2. DID YOU PERFORM "AUTO PRESET CH"?
3. PLEASE REFER TO FRONT PAGE OF THE
OWNER'S MANUAL OR REAR PANEL FOR
SUPPORT LINE INFORMATION.

Main Menu

This section describes the overview of the main menu displayed when you
press [SETUP]. For more details, see the reference page for each item.
The main menu consists of the function setting items below.
Press [SETUP].
CHANNEL SETUP
You can automatically scan the viewable channels and
remove the undesired channels.
(Refer to "Auto Channel Scan" on page 14.)
V-CHIP SETUP
You can set the viewing limitations.
(Refer to "V-chip" on page 25.)
LANGUAGE
You can change the language (English, Spanish,
French) displayed on the main menu.
(Refer to "Language Selection" on page 14.)
CAPTION
You can change the display format for closed caption,
which displays the dialogue of a TV program or other
information across the TV screen.
(Refer to "Closed Caption" on page 21.)
- HELPFUL HINTS -
e.g.) digital TV mode
- TV SETUP -
CHANNEL SETUP
V-CHIP SETUP
LANGUAGE [ENGLISH]
CAPTION [OFF]
BACK LIGHT [BRIGHT]
COLOR TEMP. [NORMAL]
DTVCC
EN
13