Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
6.
To iron with steam, push the Steam/Auto clean slider (C) to the desired
amount of steam: High Steam
the steam settings should be used with the following fabric heat
settings
: blend, wool, cotton, and linen.
7.
When finished ironing, scroll to the OFF setting. Turn the Steam/
Auto clean slider to the Dry Iron
8.
Stand iron on its heel rest and allow it to cool off.
ADDITIONAL FEATURES
Burst of Steam
Use for ironing in the vertical and horizontal position.
Press this button to generate a burst of steam.
For best performance, leave several seconds
between bursts. (D)
Spray Mist
Press the Spray Mist button to generate a spray of
water. (E) Spray Mist is used to dampen tough wrinkles
while dry or steam ironing. Do not spray silk.
3-Way Auto Shut Off
The iron will automatically shut off after 30 seconds of inactivity if left on
its soleplate or side. If left vertically on the heel rest, it will shut off after
8 minutes. When the iron is in Auto Shutoff mode, "OFF" will blink on the
Fabric/Temp. display. Simply move the iron to cancel shut down.
IR O NI N G T I P S A ND T RI C KS
•
The iron can be filled with ordinary tap water; if your water is hard, you
may want to use 50 percent distilled water and 50 percent tap water.
•
If you're unsure of the fabric's content, test a small area (on the inside
seam or hem) before you proceed to iron the entire garment or cloth.
•
Whenever ironing a garment with mixed fabrics, select the fabric
setting for the most delicate fabric. For example, when ironing a shirt
that is 65% cotton and 35% polyester, use the "blend" setting.
•
Whenever temperature settings are changed to a higher or lower
temperature, allow the iron to stand a minute or so to allow heat up or
cool down. Test garment by pressing a small hidden area to make sure
temperature of iron is correct.
6
or Low steam
. For optimal results,
position and unplug the iron.
D
E
CLEANING AND CARE
This product contains no user serviceable parts. Refer to service qualified
service personnel.
CLEANING OUTSIDE SURFACES
1.
Make sure the iron is unplugged and has completely cooled.
2.
Wipe the soleplate and outer surface with soft, damp cloth. Water
and small amounts of gentle household soaps, such as dishwashing
liquid, can be used. Never use heavy-duty cleaners, vinegar or
abrasive scouring pads that may scratch or discolor the iron.
3.
After the iron has been thoroughly dried, turn the iron back on and lightly
steam over an old cloth. This will help remove any reside left in the vents.
4.
When finished cleaning, turn iron off and allow time to cool before storing.
AUTO CLEAN™ SYSTEM
For optimal results over time, it is recommended that you clean your iron
about once a month to keep the steam vents free of build-up.
1.
Fill the water tank to the MAX fill line. Plug in the iron.
2.
Select the cotton/linen setting on the Temp display and stand the iron
on its heel while it preheats.
3.
Once the iron has reached the desired temperature; turn it off and
then unplug it from the outlet.
4.
Hold iron over a sink with the soleplate facing down.
5.
Move the Steam/Auto clean slider all the way to
the right to the Auto Clean™ setting
in that position. (F) Be careful, as hot water and
steam will come out of the vents.
6.
Continue to hold the lever in that position until all
of the water has emptied. If necessary, move the
iron side-to-side and front-to-back to aid the process.
7.
When finished, release the lever from the Auto Clean™ position and
place the iron on its heel rest.
8.
Plug the iron back in and allow it to heat for about 2 minutes to dry
out any remaining water.
STORING YOUR IRON
1.
Once the iron is turned off and unplugged from the outlet, allow it
to cool.
2.
Check that the steam lever is set to "DRY".
3.
Wrap the cord loosely around the iron.
4.
Store vertically on its heel to prevent water leaking from the soleplate.
and hold it
F
7
Publicidad
Tabla de contenido
