Cutting Procedures - Black and Decker BT1650 Manual De Instrucciones

key, and unplug the saw from the power source could result
in accidental starting causing possible serious injury.
Removing the saw blade:
► Turn blade tension knob counterclockwise to decrease
(or loosen) blade tension Fig. A.
► Pushing up from under the saw table, remove the throat plate.
► Using the "T-handle" hex key supplied with the saw, loosen
both the upper and lower blade clamp screws.
► Remove the blade.
Replacing the saw blade:
► Place the new blade through the opening in the saw table
with the teeth to the front of the saw and pointing down
toward the saw table.
► Position blade and tighten the blade clamp screw securely
using the T-handle hex key.
► Press the upper arm down to position the upper end of the
blade in the upper blade holder.
► Securely tighten the upper blade clamp screw using the
T-handle hex key.
► Turn the blade tension knob clockwise until the blade has
the desired amount of tension.
► Replace the throat plate.
Note: If the blade touches the drop foot on either side
then the drop foot must be adjusted. See section
"Adjusting Drop Foot".
OPERATION
Basic Operation of The Scroll Saw
Before starting a cut, watch the saw run. If you experience
excessive vibration or unusual noise, stop immediately.
Turn the saw off, remove the switch key, and unplug the saw.
Do not restart until locating and correcting the problem.
Note: After the saw is turned ON, a hesitation before blade
movement is normal.

Cutting Procedures

► There is a learning curve for each person who wants to
use this saw. During that period of time it is expected that
some blades will break until you learn how to use and
adjust the saw.
► Plan the way you will hold the workpiece from start to finish.
► Keep your hands away from the blade. Do not hand hold
pieces so small your fingers will go under the blade guard.
► Os dentes da lâmina apenas cortam materiais no curso inferior.
► Hold the workpiece firmly against the saw table.
► The blade teeth cut material only on the down stroke.
► Use gentle pressure and both hands when feeding the
work into the blade. Do not force the work.
► Guide the workpiece into the blade slowly because
the teeth of the blade are very small and can only remove
material on the down stroke.
► Avoid awkward operations and hand positions where a
All manuals and user guides at all-guides.com
► To get accurate cuts, compensate for the blade's tendency
► Use extra supports (tables, saw horses, blocks, etc.)
► Never use another person as a substitute for a table
► When cutting irregularly shaped workpieces, plan your
Removing Jammed Material
When backing out the workpiece, the blade may bind in the
kerf (cut). This is usually caused by sawdust clogging the kerf
or when the blade comes out of the blade holders. If this happens:
► Wait until the saw has come to a full and complete stop.
► Place the switch in the OFF position, remove the switch
► Unplug the saw from the power source.
► Remove the saw's blade and the workpiece, see section
► Wedge the kerf open with a flat screwdriver or wooden
turn saw off and wait for all moving parts to stop to avoid
serious personal injury.
Avoiding Injury
► Make sure saw is level and does not rock. Saw should
► Bolt saw to the support surface to prevent slipping, walking
► Turn saw off, remove switch key, and unplug cord from the
► Do not remove jammed cutoff pieces until blade has come
► Choose the right size and style blade for the material and
► Use only recommended accessories.
► With the exception of the workpiece and related support
► Properly support round materials such as dowel rods or
► Before removing loose pieces from the saw table,
Locking the Switch (Fig. H)
► Wait until the saw has come to a full and complete stop.
sudden slip could cause serious injury from contact with
the blade. Never place hands in blade path.
to follow the wood grain as you are cutting wood.
when cutting large, small or awkward workpieces.
extension or as additional support for a workpiece that is
longer or wider than the basic saw table.
work so it will not pinch the blade. Workpieces must not
twist, rock or slip while being cut.
key from the switch assembly. Store key in a safe place.
on "Removing the saw blade".
wedge then remove the blade from the workpiece.
Warning! Before removing loose pieces from the table,
always be on a firm, level surface with plenty of room for
handling and properly supporting the workpiece.
or sliding during operations like cutting long, heavy boards.
power source before moving the saw.
to a full and complete stop.
type of cut you plan to do.
devises, clear everything off the saw table before turning
the saw on.
tubing because they have a tendency to roll during a cut
causing the blade to "bite". To avoid this, always use
a "V" block or clamp workpiece to a miter gauge
turn saw off and wait for all moving parts to stop.
ENGLISH • 27