Precautions; Preset Mode Timing Table - Sony CPD-E540 Manual De Instrucciones

Preset and user modes
When the monitor receives an input signal, it automatically matches the
signal to one of the factory preset modes stored in the monitor's memory
(see "Preset mode timing table" on
to provide a high quality picture
page i) . If the input signals does not match one of the factory preset
modes, the monitor automatically provides the most appropriate picture
for the input signal that is within the range of the vertical or horizontal
frequencies (page 7) corresponding to the Generalized Timing Formula.
When the picture is adjusted, the adjustment data is stored as a user mode
and automatically recalled whenever the same input signal is received.
Power saving function
This monitor meets the power-saving guidelines set by VESA,
S
TAR, and NUTEK. If no signal is input to the monitor from your
computer, the monitor will automatically reduce power consumption as
shown below.
Power mode Power consumption
≤ 135 W
normal operation
1 ≤ 3 W
active off*
2
(deep sleep)*
power off Approx. 0 W
1
* When your computer enters power saving mode, NO SIGNAL appears
on the screen. After a few seconds, the monitor enters power saving
mode.
2
* "Deep sleep" is power saving mode defined by the Environmental
Protection Agency.
Design and specifications are subject to change without notice.
8

Precautions

Warning on power connections
• Use the supplied power cord. If you use a different power cord,
E
NERGY
• Before disconnecting the power cord, wait at least 30 seconds
! (power)
indicator
green
• After the power is turned on, the screen is demagnetized
orange
off
The equipment should be installed near an easily accessible
outlet.
Installation
Do not install the monitor in the following places:
• on surfaces (rugs, blankets, etc.) or near materials (curtains,
• near heat sources such as radiators or air ducts, or in a place
• in a place subject to severe temperature changes
• in a place subject to mechanical vibration or shock
• on an unstable surface
• near equipment which generates magnetism, such as a
• near or on an electrically charged metal surface
• inside an enclosed rack
Protection
• Do not put foreign objects into the monitor.
• Disconnect the monitor if environment exceeds 60°C/140°F.
• Ensure AC power cord is not trapped under furniture, TV, etc.
• Do not overload wall outlets, extension cords, or convenience
• Never spill liquid of any kind on the monitor.
Notes on cleaning the screen's surface
• The screen's surface is covered with a thin anti-reflective
• Do not use any type of abrasive pad, alkaline cleanser, scouring
• If you use a glass cleaning liquid, do not use any type of cleaner
• Do not rub, touch, or tap the surface of the screen with sharp or
Notes on cleaning the cabinet
• Clean the cabinet, panel and controls with a soft cloth lightly
• Do not use any type of abrasive pad, scouring powder or
be sure that it is compatible with your local power supply.
For the customers in the U.S.A.
If you do not use the appropriate cord, this monitor will not
conform to mandatory FCC standards.
Example of plug types
for 100 to 120 V AC
after turning off the power to allow the static electricity on the
screen's surface to discharge.
(degaussed) for about a few seconds. This generates a strong
magnetic field around the screen which may affect data stored
on magnetic tapes and disks placed near the monitor. Be sure to
keep magnetic recording equipment, tapes, and disks away
from the monitor.
draperies, etc.) that may block the ventilation holes
subject to direct sunlight
transformer or high voltage power lines
receptacles beyond their capacity.
coating to enhance the ergonomic characteristics of the
monitor. To ensure that the coating is not damaged, use a soft
cloth to clean the screen's surface. If necessary, use a soft cloth
lightly moistened with a mild detergent solution, such as hand
soap, to wipe the screen.
powder, or solvents such as alcohol or benzene as they might
damage the anti-reflective coating.
containing an anti-static solution or similar additive as this may
scratch the screen's coating.
abrasive items such as a ballpoint pen or screwdriver. This type
of contact may result in a scratched picture tube.
moistened with a mild detergent solution.
solvent, such as alcohol or benzene.
for 200 to 240 V AC