Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Hitch Shown In Proper Position
Equipment Required: Lubricant or Soapy water
Fastener Kit: 75664F
Wrenches: 18mm, 19mm
Exhaust hanger bracket
Rubber Exhaust Hanger
1
Qty. (4)
Hex Bolt M12 x 1.75 x 40mm CL8.8
1.
Lower exhaust by removing two (2) bolts which attach exhaust hanger bracket to driver's side frame rail. Discard bolts.
Note: Re-attachment of exhaust hanger bracket may be made easier by removing rubber exhaust hanger from hanger bracket.
2.
Detach the rubber isolator from the front exhaust hanger located forward of muffler, just behind rear axle. Spraying a lubricant
on the metal hanger rod and the rubber isolator helps removal.
3.
Rotate the hitch into position over the exhaust and align the slots to the existing weld nuts. Note: Driver's side bracket will be
sandwiched between frame rail and exhaust hanger bracket. Secure hitch and exhaust hanger bracket with M12 x 1.75 x
40mm bolts and conical toothed washers provided with hitch.
4.
Tighten all fasteners to the required torque specification.
5.
Raise exhaust back into position and reattach to rubber isolators.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent
entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a
vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and
SAE J684.
z
2009 Cequent Towing Products
Installation Instructions
Fascia
1
2
Tighten all M12 x 1.75 CL8.8 fasteners with torque wrench to 68 Lb.-Ft. (92 N*M)
Ford Flex
Do Not Exceed Lower of Towing Vehicle
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
Wiring Access Location: SUV1, SUV2
Vehicle Frame
2
Qty. (4)
Conical Toothed Washers ½"
Sheet 1 of 3
75664N
Part Numbers:
75664
87545
44620
78203
Manufacturer's Rating or
Max Gross
Trailer WT (LB)
4000 (1816 Kg.)
4000 (1816 Kg.)
Existing
Weldnuts
2-27-09
Max Tongue
WT (LB)
400 (182 Kg.)
400 (182 Kg.)
12
Rev. C
Publicidad
Manuales relacionados para Cequent Towing Products 75664
Resumen de contenidos para Cequent Towing Products 75664
- Página 1 Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 3 75664N 2-27-09 Rev. C 2009 Cequent Towing Products...
- Página 2 Ne jamais utiliser une torche pour découper un accès ou un trou de fixation. Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. Feuillet 2 sur 3 75664N 2-27-09 Rév. C 2009 Cequent Towing Products...
- Página 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684. Hoja 3 de 3 75664N 2-27-09 Rev. C 2009 Cequent Towing Products...