Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Hitch Shown In Proper Position
Equipment Required: Fishwire (provided)
Fastener Kit: F41549 or KA-8002-291
Wrenches: ¾"
Drill Bits: 7/16"
Fasteners typical
Both sides
Make sure blocks do not
Overlap inside frame before
Tightening.
1
Qty. (6)
Carriage Bolt ½-13
2
Qty. (6)
Block ¼ X 3"
On vehicles with vibration dampener assembly mounted to driver's side frame rail, remove and retain dampener and
fasteners for re-installation after hitch installation. See Figure 2 for dampener re-installation.
NOTE: Vibration dampener cannot be re-installed on Flareside models.
NOTE: Lowering spare tire may ease installation
1.
Raise hitch into position, aligning holes in hitch side brackets with holes in vehicle frame as shown.
2.
Install ¼ X 3 block and carriage bolt thru end of frame into rearmost slot in frame, each side. Fasten with lock washers and nuts.
Finger-tighten only at this time.
3.
Fishwire ¼ X 3 blocks and carriage bolts, 2 each side, thru forwardmost square hole in side of frame rail and into holes aligned
with holes in hitch side bracket. Fasten with lock washers and nuts.
NOTE: Make sure blocks do not overlap inside frame before tightening.
NOTE: On vehicles with Vibration Dampener assembly, see Figure 2 to install dampener before tightening fasteners.
4.
Raise spare tire back into position.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2003, 2005 Cequent Towing Products
Installation Instructions
Ford F-150
Lincoln Mark LT
Wiring Access Location: PU3
Figure 1
3
4
Tighten all ½-13 GR5 fasteners with torque wrench to 75 Lb.-Ft.
Sheet 1 of 6
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
Hitch type
Trailer WT (LB)
Weight Distributing
Weight Carrying
Ball Mount
Shackle bracket
Typical both sides
Qty. (6)
Lock Washer ½"
Qty. (6)
Hex Nut ½-13
N75156
Part Numbers:
75156
33077
87195
Max Gross
Max Tongue
WT (LB)
8000
800
6000
600
5-23-05
Rev. C
Form: F205 Rev A 5-6-05
Publicidad
Manuales relacionados para Cequent Towing Products 75156
Resumen de contenidos para Cequent Towing Products 75156
- Página 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 6 N75156 5-23-05 Rev. C 2003, 2005 Cequent Towing Products Form: F205 Rev A 5-6-05...
-
Página 2: Installation Instructions
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 2 of 6 N75156 5-23-05 Rev. C 2003, 2005 Cequent Towing Products Form: F205 Rev A 5-6-05... -
Página 3: Numéros De Pièce
Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. Feuille 3 de 6 N75156 23-5-05 Rév. C 2003, 2005 Cequent Towing Products Form: F205 Rev A 5-6-05... - Página 4 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. Feuille 4 de 6 N75156 23-5-05 Rév. C 2003, 2005 Cequent Towing Products Form: F205 Rev A 5-6-05...
-
Página 5: Números De Partes
Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York. V.E.S.C. Regulación V-5 y SAE J684. Hoja 5 de 6 N75156 23-5-05 Rev. C 2003, 2005 Cequent Towing Products Form: F205 Rev A 5-6-05... - Página 6 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York. V.E.S.C. Regulación V-5 y SAE J684. Hoja 6 de 6 N75156 23-5-05 Rev. C 2003, 2005 Cequent Towing Products Form: F205 Rev A 5-6-05...