Ryobi PBLRT01 Manual Del Operador página 9

NOTICE:
To prevent damage to the spindle or spindle lock, always
allow motor to come to a complete stop before engaging
the spindle lock.
APPLICATIONS
You may use this product for the purposes listed below:
 Carving, engraving, etching, polishing, cleaning, removing
rust, sanding, cutting, grinding, sharpening, drilling, and
routing
HANGING THE ROTARY TOOL
WARNING:
Do not use the tool hanger to hang the tool from your
body. Do not suspend the tool overhead. Suspend only
from stable and secure locations.
 Turn the tool off and remove accessories.
 Swing the tool hanger out and hang the tool on a suitable,
stable structure.
 To mount the rotary tool console, use the key hole hanging
feature. Screws should be installed so that the center
distance is 4 in.
INSTALLING/REMOVING BATTERY PACK
See Figure 2, page 15.
To install:
 Insert the battery pack.
 Make sure the latches on each side of the battery pack
snap into place and the battery pack is secured in the
product before beginning operation.
To remove:
 Depress the latches on each side of the battery pack.
For complete charging instructions, see the operator's
manuals for your battery pack and charger.
WARNING:
Battery products are always in operating condition.
Therefore, the switch should always be locked when not
in use or carrying at your side.
QUICK-CHANGE COLLET
See Figure 3, page 15.
NOTE: The tool ships with a preinstalled collet that is
machined to precision tolerances to fit accessories
with 1/8 in. diameter shanks. When installed, the quick
change collet allows the user to change accessories
without tools and without removing the collet from the
shaft. The quick change collet is not compatible with
1/16" in. shanks.
OPERATION
To remove/install the quick change collet:
 Remove the battery pack from the tool.
 Depress and hold the spindle lock button and rotate the
shaft by hand until the spindle lock engages the shaft,
preventing further rotation.
 With the spindle lock engaged, place the included 3/8 in.
wrench on the bottom threaded end of the quick-change
collet and turn counterclockwise to loosen. Continue
turning counterclockwise to remove the collet from the
tool.
 Remove the quick-change collet.
 To install, engage the spindle lock. Place the quick-
change collet on the shaft and begin threading on by
hand until there is resistance. Then use the included 3/8
in. wrench on the bottom threaded end of the collet and
rotate clockwise until tightly secured.
WARNING:
Always use the collet which matches the shank size of the
accessory you plan to use. Never force a large diameter
shank into a collet. The accessory should fit smoothly into
the collet, but you should be able to tighten the accessory
firmly and securely with the quick-change collet.
INSTALLING/REMOVING ACCESSORIES
See Figure 4, page 15.
To install:
 Remove the battery pack from the tool.
 Choose an accessory that fits the collet and is suitable
for the application you are attempting.
 Ensure the quick-change collet is securely installed on
the shaft.
 While depressing the spindle lock, use your hand to
loosen the collet by rotating the sleeve counterclockwise.
 Insert the shank of the accessory into the collet until the
shank bottoms out, then pull it out 1/16 in. to allow for
expansion when the accessory gets hot.
 Rotate the collet sleeve clockwise until clicking stops and
the accessory shank is gripped by the collet.
NOTE: If sleeve cannot be tightened or loosened
sufficiently by hand, use the included 3/8 in. collet wrench
on the top hexed area of the collet. Turn clockwise to
tighten or counterclockwise to loosen.
To remove:
 Remove the battery pack from the tool.
 Engage the spindle lock.
 Turn the collet sleeve counterclockwise to loosen.
 Remove the accessory.
9 — English