DeWalt 49A70003038 Manual Del Operador página 7

Embolsadora posterior triple
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

7.
Slide the hinge pin (711-05079) into the hole located on the mounting tab, as
shown in Figure 11. Use the cut-out windows (see inset in Figure 11) to line up
the hinge pin on the other side and push pin all the way in until it reaches the
end-stop. At this point the pin clips into place and is secured by a tab in the
bagger cover.
Figura 12
8.
Open hood by pushing in on the
rear, right-side tab with your right hand (1), and lifting the cover with your
left hand in the center rear of the bagger cover (2) as shown in Figure 12.
9.
Install all three bag assemblies (664-05681) onto the hanger assembly by
inserting the front edge in first (1), and then setting the back edge down until
it fits into the assembly (2), as shown in Figure 13.
Installing the Boot Assembly - 48" Triple Bagger
1.
With the tractor's
outer and inner
discharge chutes
raised up and held
open (1), install the
boot assembly (819-
011300) by placing
the hole on the boot
assembly bracket on
the tab located on
the top, right rear
of the deck (2), as
shown in Figure 14.
2.
Pivot the boot
assembly forward,
sliding under the
discharge chutes
raised in Step 2, until the pin on the boot assembly bracket aligns with the
slot on the deck. See (3) in Figure 14.
NOTE
: You should hear a click when the center tab on the boot assembly bracket snaps into
place on the deck.
3.
Secure the boot assembly to the cutting deck using wing knob (720-04122)
from hardware pack 689-02619. See inset of Figure 14.
NOTE
: The inner and outer spring-loaded discharge chutes will remain propped on the boot
assembly bracket, creating a seal between the deck and the boot assembly.
ASSEMBLY & INSTALLATION
Figura 13
1
2
3
Figura 14
7
Installing the Boot Assembly - 54"/60" Triple Bagger
1.
Raise the deck to its
highest position.
2.
With the tractor's
outer and inner
discharge chutes
raised up and held
open (1), install the
boot assembly (819-
011280) by placing
the hole on the boot
assembly bracket on
the tab located on
the top, right rear
of the deck (2), as
shown in Figure 15.
3.
Pivot the boot assembly forward, sliding under the discharge chutes raised in
Step 2, until the pin on the boot assembly bracket aligns with the slot on the
deck. See (3) in Figure 15.
NOTE:
You should hear a click when the center tab on the boot assembly bracket snaps into
place on the deck.
4.
Secure the boot assembly to the cutting deck using wing knob (720-04122)
from hardware pack 689-02619. See inset of Figure 15.
NOTE:
The inner and outer spring-loaded discharge chutes will remain propped on the boot
assembly bracket, creating a seal between the deck and the boot assembly.
Installing the Hose
1.
Thread the upper end of the
hose (764-05275) securely
into the upper chute
support. There are two tabs
on the lower inside part of
the upper chute support to
allow for secure threading.
See Figure 16.
NOTE:
The hose and upper chute
support are left-hand threaded.
Thread counterclockwise until
secure.
2.
Slide the hose over the boot
assembly mounted on the cutting
deck, as shown in Figure 17.
3.
Make sure the connection is
secure and there are no gaps
between the hose and the boot
assembly.
4.
If open, close the grass catcher
cover prior to mowing.
1
2
3
Figura 15
Figure 16
Figure 17

Publicidad

Tabla de contenido
loading

Productos relacionados para DeWalt 49A70003038

Este manual también es adecuado para:

49a70004038

Tabla de contenido