GBC AutoFeed+ Serie Manual De Instrucciones página 6

AutoFeed+ Shredding Capability
CAN shred the following:
• Stapled paper, 1 inch / 25 mm within the corner
• 26/6 and 24/6 or smaller staples
• Small sized paper
• Paperclipped paper, 1 inch / 25 mm within the corner
• Capable of shredding small/medium paperclips
(max. wire thickness = .035 inches / .9 mm)
• 65-100gsm paper
CAN shred (through the manual feed slot):
Glossy paper or a sheet
Thick paper or card
covered with print on both
<200gsm
sides.
CANNOT shred the following:
Heavy duty staples.
Check the staple leg
length is not greater
than .23 inches / 6 mm.
Bulldog clips
Adhesive labels
No aerosols
Lubrication of the Shredder
GBC recommends using an oil sheet after the bin has been
emptied three times (and every three bin emptying after this).
Insert the oil sheet into the manual feed slot and NOT in
the auto-feed chamber. Using an oil sheet in the auto-feed
chamber will contaminate the feed rollers preventing the
auto-feed mechanism shredding. Follow the maintenance
instructions if the rollers become contaminated.
10
• 11'' x 17'' folded in half max. 2 sheets
• 300 sheets
• 80gsm paper
- Letter - 8.5" x 11"
- 1/2 Sheet - 5.5" x 8.5"
- Tabloid - 11" x 17"
Multiple folded sheets
(11'' x 17'' sheets folded
in half).
Large clips. Check the length
Plastic sheets,
of the paperclip is not longer
laminated documents,
than 1.25 inches / 32 mm.
plastic folders.
Magazines or other
Bound documents
documents bound by
multiple staples or clips.
No Liquid Oil No CDs & DVDs
Maintenance
The rollers on the auto-feed mechanism may become dirty
over time, please wipe clean with a dry cloth to maintain
maximum product performance.
The auto-start infrared sensor, located in the paper feed
entry-slot, can occasionally become covered in paper-
dust causing the shredder to run despite no paper being
fed into the machine. Switch the shredder off at the rear
of the machine and carefully clean the sensor using a
cotton-swab.
Limited Warranty
Cutter warranties vary by model. Limited 2 year warranty on the shredder unit.
ACCO Brands USA LLC, Four Corporate Drive, Lake Zurich, IL 60047-8997 (in Canada, ACCO Brands Canada Inc., 5 Precidio Court, Brampton,
ON L6S 6B7; and in Mexico, ACCO Mexicana, S.A. de C.V. Av. Circuito Industrial Norte #6 Parque Industrial Lerma 52000, Lerma Edo. De México)
(each, respectively, "ACCO Brands") warrants to the original purchaser that the cutters of these GBC® AutoFeed Shredders are free from defects
in workmanship and material under normal use and service for a period of 2 years after purchase and all other parts are free from defects in
workmanship and material under normal use and service for a period of 2 years after purchase.
ACCO Brands' obligation under this warranty is limited to replacement or repair, at ACCO Brands' option, of any warranted part found defective by
ACCO Brands without charge for material or labor. Any replacement, at ACCO Brands' option, may be the same product or a substantially similar
product that may contain remanufactured or refurbished parts. This warranty shall be void in the following circumstances:
(i) if the product has been misused,
(ii) if the product has been damaged by negligence or accident, or
(iii) if the product has been altered by anyone other than ACCO Brands or ACCO Brands' authorized agents.
For warranty execution, please call:
1-800-541-0094 in the USA
1-800-263-1063 in Canada
01-(55)-1500-5700 / 5778 in Mexico
Or go to www.gbc.com to register your product.
TO THE EXTENT ALLOWED BY APPLICABLE LAW, THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESSED WARRANTIES.
REPRESENTATIONS OR PROMISES INCONSISTENT WITH OR IN ADDITION TO THIS WARRANTY ARE UNAUTHORIZED AND SHALL NOT
BE BINDING ON ACCO BRANDS. TO THE EXTENT PERMITTED BY APPLICABLE LAWS, ANY IMPLIED WARRANTIES (IF APPLICABLE)
ARE LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY. SOME STATES AND JURISDICTIONS DO NOT ALLOW LIMITATIONS
ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU. TO THE EXTENT PERMITTED
BY APPLICABLE LAW, IN NO EVENT SHALL ACCO BRANDS BE LIABLE FOR ANY SPECIAL, INCIDENTAL, PUNITIVE, EXEMPLARY,
CONSEQUENTIAL OR SIMILAR DAMAGES, WHETHER OR NOT FORSEEABLE. SOME STATES AND JURISDICTIONS DO NOT ALLOW
THE EXCLUSION OR LIMITATION OF SPECIAL, INCIDENTAL, PUNITIVE, EXEMLARY, CONSEQUENTIAL, OR SIMILAR DAMAGES, SO THE
ABOVE EXCLUSION OR LIMITATION MAY NOT APPLY TO YOU.
FOR CONSUMERS WHO HAVE THE BENEFIT OF CONSUMER PROTECTION LAWS OR REGULATIONS IN THEIR JURISDICTION OF
PURCHASE OR, IF DIFFERENT, IN THEIR JURISDICTION OF RESIDENCE, THE BENEFITS CONFERRED BY THIS WARRANTY ARE IN
ADDITION TO ALL RIGHTS AND REMEDIES CONVEYED BY SUCH CONSUMER PROTECTION LAWS AND REGULATIONS.
To the extent permitted by law, this warranty is not transferable and will automatically terminate if the original product purchaser sells or otherwise
disposes of the product.
This warranty gives you specific legal rights. Other rights, which vary from jurisdiction to jurisdiction, may exist. In addition some jurisdictions do
not allow (i) the exclusion of certain warranties, (ii) limitations on how long an implied warranty lasts and/or (iii) the exclusion or limitation of certain
types of costs and/or damages, so the above limitations may not apply.
FCC CLASS B NOTICE
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to If this
equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
CANADA CLASS B NOTICE
This Class B digital apparatus complies with Canadian ICES-003
MODIFICATIONS
Any modifications made to this device may void the authority granted to the user by the FCC and/or by Industry Canada to operate this equipment.
ACCO is a registered trademark of ACCO Brands.
Copyright © 2021 ACCO Brands. All rights reserved.
*ACCO Brands North America accepts no liability for product performance or safety when other types or brands of lubricants are used on any
part(s) of this machine.
English
11