Hudora BigWheel 215 Instrucciones De Montaje Y De Uso página 9

INSTRUCTIONS ON ASSEMBLY AND USE
EN
• Push the handlebar rod as far as it will go into the handlebar
stem.
• Close the quick release lock by pushing the lever down to the
handlebar stem.
• Pull the lever on the right or left above the footboard to release
the folding mechanism.
• Fold the scooter by moving the handlebars towards the rear
wheel until the folding mechanism audibly clicks into place.
(Fig. 9) If necessary, you can also loosen the handlebar. To do
this, proceed in reverse order to step 2 of the assembly instruc-
tions and as shown in Fig. 2.
USAGE INSTRUCTIONS
NOTHING'S EASY AT FIRST ...
... most accidents happen to "beginners" within the first ten
minutes. Particular care should be taken during this stage.
DRIVING INSTRUCTIONS
The scooter moves when a foot is used to regularly push off, just
as with well-known children's scooters. Braking is no problem
either – simply step on the friction brake over the back wheel
(mudguard).
We recommend folding the scooter by hand after each use or
using the stand. The side stand is in the direction of movement
located on the left hand side under the deck. Its use is ensured
through simply folding and unfolding. Aluminium is a good and
light material but should also be handled carefully as it is not as
hard as steel, for example.
MAINTENANCE AND STORAGE
Use a dry or damp cloth only to clean the product; do not use
special cleaning agents! Check the product for damage or trac-
es of wear and tear before and after each use. Do not make any
structural changes. For your own safety, please use original spare
parts only. These can be sourced from HUDORA. If parts become
damaged or if sharp edges or corners should develop, the product
may not be used any more. If in any doubt, please contact our
service team (http://www.hudora.de/). Store the product in a safe
place where it is protected from the elements, cannot be damaged,
and cannot injure anyone.
Replace damaged or worn assembly parts in order to ensure the
safety of your scooter.
WHEEL CHANGE
Replacement wheels are available as accessories from http://
www.hudora.de/ and should be replaced when they are worn
down. To change the wheels, loosen the axle fitting with two Allen
keys and take the wheels off the axle. A screwdriver or Allen key
can be used to push the bearings out of the wheel to use them
in the new wheel. However, it is usually advisable to change the
bearings when the wheels are changed. Put the bearings into the
new wheel with the bolt spacer and mount them to the frame with
the axle screws. Make sure the axle has been screwed on tightly
before starting again!
BEARINGS
Your kick scooter is equipped with precision ball bearings, which
were filled with grease under high pressure, during manufacture.
For this reason, the rollers of the kick scooter only run lightly and
swiftly, while under load. Bearings are maintenance-free, but they
are wear parts. Caution! Worn bearings make conspicuous audi-
ble noises and their function is constrained. In order to maintain
optimal riding pleasure and to ensure lasting safety, you should
replace bearings, as soon as they begin to exhibit signs of being
worn. In the case of full load and daily use we recommend the
replacement of the rollers and bearings twice a year. Bearings are
available as accessories under http://www.hudora.de/.
DISPOSAL ADVICE
At the end of the product's life, please dispose of it at an appro-
priate collection point provided in your area. Local waste man-
agement companies will be able to answer your questions on this.
SERVICE
We make every effort to deliver faultless products. If faults do arise
however, we put just as much effort into rectifying them. There-
fore, you can find numerous information on the product, replace-
ment parts, solutions to problems and lost assembly manuals at
http://www.hudora.de/.
SPARE PARTS AND ORIGINAL
ACCESSORIES AVAILABLE AT:
http://www.hudora.de/
All images are examples of the design.
9/24