Optional Accessories - Stanley STHM10 Manual De Instrucciones

ENGLISH (
Original Instructions)
before unplugging.
Various types of chisels are available as an option.
Only Stanley recommended accessories should be used
with this product.
WARNING:
Do not use this tool to mix or pump easily combustible
u
or explosive fluids (benzine, alcohol, etc.).
Do not mix or stir inflammable liquids labelled accord-
u
ingly.
Accessory maintenance (Fig B)
Accessory maintenance at the right time guarantees optimal
results in application and a long and efficient accessory life.
Grind the chisels on grinding discs. Refer to Fig. B for the
appropriate angles of the following chisels:
Pointed chisel (8)
Flat chisel (9)
WARNING! These chisels can be reground only a
limited number of times. If in doubt, contact your
dealer for recommendations.
WARNING! Ensure that the cutting edge does not
show discolouration caused by too much pressure.
This may impair the hardness of the accessory.
MAINTENANCE
Your Stanley corded/cordless appliance/tool has been
designed to operate over a long period of time with a
minimum of maintenance. To ensure satisfactory operations,
the tool must be maintained and cleaned regularly
WARNING: To reduce the risk of injury, turn
unit off and disconnect machine from power
source before installing and removing accessories,
before adjusting or changing set-ups or when making
repairs. Be sure the trigger switch is in the OFF position.
An accidental start-up can cause injury.
· This machine is not user-serviceable. If problems occur
contact an authorised repair agent.
· The tool will automatically switch off when the carbon
brushes are worn.
WARNING! Before performing any maintenance on corded/
cordless power tools:
· Switch off and unplug the appliance/tool.
· Or switch off and remove the battery from the appliance/
tool if the appliance/tool has a separate battery pack.
· Or run the battery down completely if it is integral and
then switch off.
· Unplug the charger before cleaning it. Your charger does
not require any maintenance apart from regular cleaning.
· Regularly clean the ventilation slots in your appliance/
tool/ charger using a soft brush or dry cloth.
· Regularly clean the motor housing using a damp cloth.
Do not use any abrasive or solvent-based cleaner.
· Regularly open the chuck and tap it to remove any dust
from the interior (when fitted).
Replace the Carbon Brush (Fig. D)
20
Lubrication
· Regularly replace and check the carbon brushes.
Replace it in time when it is worn to the abrasive
boundary line. Keep the carbon brush clean and make
it freely slide in the brushing range. Two brushes shall
be eplaced at the same time.
· Use the cross screwdriver to counterclockwise unscrew
the screws, open the bottom cover (8) with a flat
screwdriver to counterclockwise open the brush cover,
you can remove the brush as shown in the Fig. D, and
put the new brush, and then clockwise fasten the brush
cover, finally put the bottom cover, and then use the
cross screwdriver to tighten it properly.
· Open the cap of the lube oil-injection inlet (5), check
the lube oil in the gearbox, if the lube oil is dirty or
insufficient, replace or add the adequate amount of lube
oil provided by the company.
Cleaning
WARNING! Blow dirt and dust out of the
main housing with dry air as often as dirt is
seen collecting in and around the air vents.
Wear approved eye protection and approved dust
mask when performing this procedure.
WARNING! Never use solvents or other
harsh chemicals for cleaning the non-
metallic parts of the tool. These chemicals may
weaken the material of the parts. Use only mild
soap and damp cloth to clean the tool. Never let any
liquid get inside the tool,cleaning of gasoline or
other chemicals, never immerse any part of the tool
into liquid.
IMPORTANT! To ensure product SAFETY and
RELIABILITY,
adjustment (other than those listed in this manual)
should be performed by authorized service centers
or other qualified organizations, always using
identical replacement parts. Unit contains no user
service able parts inside.

Optional Accessories

WARNING! Since accessories, other than those
offered by Stanley, have not been tested with this
product, use of such accessories with this tool could be
hazardous. To reduce the risk of injury, only Stanley,
recommended accessories should be used with this
product.
Various types of SDS MAX drill bits and chisels are available
as an option.
Consult your dealer for further information on the
appropriate accessories.
Protecting The Environment
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your Stanley product
repairs, maintenance and