stayer VENTO L20 Manual De Instrucciones página 17

Assembly
Before operating the tool, make sure that the
components are mounted correctly.
Firmly tighten all screws, bolts and nuts
Machine holding belt
VENTO 2400 D / VENTO 36V L20
The equipment includes a belt 4 for ergonomically
positioning the machi ne. For assembly of the holding belt
4:
- Open the belt 4 by pushing its lock.
- Pass the belt 4through the fastening ring 17.
- Adjust the length of belt 4 according to the user's
stature and depending on how it is held.
Emptying of collection bag
Switch off the tool and disconnect the plug
- Wait until the impeller comes to a standstill befare
removing the collection bag from the tool.
- Open the zipper of the collection bag and empty it
completely
- Compostic material does not be long with domestic
waste
VENTO 2400 D / SP 700
Cord restraint
- Hook the loop in the extension cord over restraint 5 as
illustrated.
- Pull tight to secure the extension cord.
-
lllustrated description
1
1Lower blower/suction tube
2 Upper blower/suction tube
3
Collection bag
4 Shoulder strap
5
Cord restraint
6 On/off switch
7
Switch for selecting operating mode
8 Supporting wheels
9
Ventilation slots
10 Main handle
11 Guide handle
12 Vacuum opening
13 Blower opening
14 Motor set
15 Suction socket
16 Fastening hales
OPERATING INSTRUCTIONS
3.
On/Off
The SP700, VENTO 36V L20 and VENTO L20 models
only have a blower function.
Switch on/off the tool by pushing switch 6 in "l"/"O" position
Before switching on the tool, ensure that it is not in contact
with any object.
After switching off the tool the motor continues to run for
ENGLISH
17
a few seconds.
VENTO 36V L20
TURBO mode
The VENTO 36V L20 model has a button on the handle
that activates the TURBO mode for 2 seconds when
pressed. The TURBO mode increases the blowing air
volume for 2 seconds to clean hard-to-reach areas.
VENTO 2400 D
Blowing
Select blowi ng mode with switch 7as illustrated ( on ly
when tool is switched off).
Vacuuming
- Ensure that collection bag 3 is attached to the tool.
- Select vacuuming mode with switch 7 as illustrated
(only when tool is switched off)
Do not vacuum solid objects such as stones, broken
glass, pieces of metal
- Do not vacuum liquids.
- Do not vacuum large volumes of leaf material at one
time thus avoiding clogging of the vacuuming opening
and blocking of the shredder impeller.
- The shredding intensity depends on the size of the
leaf material and its residual moisture.
When the tool suddenly stops, immediately switch it off,
disconnect plug from power source, and remove any
jammed material between shredder impeller and housing.
- Regularly empty collection bag 3 (the vacuum
capacity decreases considerably when the collection
bag is full).
Holding and guiding the tool
While working, always hold the tool at the grey
coloured grip area(s).
- Use supporting wheels 8 for easy guiding the tube
along the ground.
- For optimal results keep a 5 - 10 cm distance to the
ground.
Troubleshooting
The following listing shows problem symptoms, possible
causes and correctiva actions (if these do not identify
and correct the problem, contact your dealer or service
station).
Switch off the tool and disconnect the plug before
investigating the problem.
Tool does not operate
- No power supply. Check power supply (power
cable,circuit breakers, fuses, batteries)
- Plug not connected. Connect plug.
- Extension cord damaged. Replace extension cord.
- On/off switch defective. Contact dealer/service
station.
- Worn carbon brushes. Canta et dealer/service
17