Descargar Imprimir esta página

Paaschburg & Wunderlich HIGHSIDER 7 LED Instrucciones De Montaje página 3

Publicidad

Idiomas disponibles

Idiomas disponibles

Thank you for buying a HIGHSIDER product. Because of our passion for motorcycles all our products are designed to meet your needs as a motorcyclist. We wish you always a safe and pleasant ride with your new HIGHSIDER product
from Paaschburg & Wunderlich GmbH.
Only when professionally installed is the statutory warranty and driving safety fulfilled. Pay attention to the information in the operating instructions of the vehicle or specifications of the vehicle manufacturer. Ask a specialist or mechanic
to do the installation if you are unsure yourself! Failure to follow the assembly instructions can damage your vehicle and void the warranty. This is necessary to not affect the riding safety. No liability is accepted for consequential
damage. The unauthorized reworking and / or modification of the product can lead to the failure of the function and is not permitted. Never look directly into the light of the LED's! This light module is approved for use on motorcycles.
The product complies with the current ECE standard when installed correctly. This means no registration or carriage of documentation is needed when installing it onto your motorcycle.
Please keep these instructions for later use!
Scope of delivery:
 1 pc. headlight insert
Installation of the headlight insert:
1. Disconnect the battery before fitting. Make sure that your vehicle is standing securely. Before the permanent installation, we recommend that you carry out a function test of the light.
ATTENTION:
Only connect to a 12V DC vehicle electrical system!
2. Low beam / High beam (Fig.1/ Fig.2). Position light (Fig.3). The parking light/position light is designed as a ring along the outer edge of the headlight.
3. If the LED insert is installed in a suitable lamp housing, sufficient ventilation must be ensured to prevent the LED headlight from overheating. Failure to do so will void the warranty!
4.
ATTENTION:
After mounting, insert the flat plugs into the supplied 3-pin plug housing. Ensure the correct assignment according to the sketch below.
5. Lay all cables properly. Do not kink the cables. Insulate loose cable ends well!
6. On vehicles with CAN bus system or ABS system, error messages may occur due to the lower electrical resistance of the LED unit. In this case, an additional resistor can help.
7.
ATTENTION:
After installation, the correct functioning of the ABS system or CAN bus system must be checked!
8.
ATTENTION:
Check the correct function of the light system before every ride.
White cable
Red cable
Black cable
Before each ride: It is the duty and responsibility of the rider to regularly check and maintain the safety-related vehicle parts. Before starting your journey, check the correct adjustment and function of the products and the tightness of all screwed connections.
Warranty: Take the time to do a 100% professional job of installing the products. Take into account all our installation and safety instructions.
A faulty, improper installation or handling of the product will void the warranty.
Maintenance/Care: Do not use aggressive detergents to care for the products. The products can be perfectly cleaned with a simple, lukewarm detergent solution. Contact with brake fluid, brake cleaner, fuel, etc. should be avoided. Immediately pick up any unintentionally
applied impurities with a soft cloth and clean the surface with detergent solution
Enviromental Information: This product may not be disposed in the normal household rubbish at the end of its lifetime. The disposal can be done through the Paaschburg u. Wunderlich customer service or a local return and waste collection institution.
HIGHSIDER Tips & Tricks on
https://www.youtube.com/c/HIGHSIDERTippsTricks
Exclusion of liability and warranty regulation:
In the event of improper handling, installation or use of the device, warranty and guarantee claims may expire. Due to the non-verifiability of the correct application, Paaschburg und Wunderlich GmbH assumes no liability for direct or indirect damage or consequential damage resulting from the operation of the device.
This does not apply if the damage is based on intent or gross negligence on the part of Paaschburg & Wunderlich GmbH, or if the damage consists in injury to life, limb or health, or Paaschburg & Wunderlich GmbH has culpably violated an essential contractual obligation (cardinal obligation).
Paaschburg & Wunderlich GmbH, Am Alten Lokschuppen 10a, D-21509 Glinde (GER),
Tel.: +49 (0) 40 248 277-0; E-Mail:
sales@pwonline.de
226-020A_Rev01_2022-01
Please read this manual carefully prior to installation
Find useful additional accessories like stem extensions, resistors, electronic relays, adapter cables and other equipment in our Webshop!
Plug – cable assignment
:
and safety instructions
Mounting
HIGHSIDER TYPE 7 LED main headlight insert
Cable connection (connect to 12V DC only)
white cable = low beam (+)
red cable = high beam (+)
black cable = ground (–)
green cable = LED-position light(+)
black cable = ground (–)
You can find more
products at:
www.highsider-germany.de
A: 143 mm
3 pin plug:
www.highsider-germany.de
All rights reserved. Changes and errors are excepted.
A
Seite 3 von 5

Publicidad

loading