Location Of Parts - Sharp EM-KS1 Manual De Instrucciones

6
What's in the Box:
• E-scooter
• User manual
• Warranty card
• 1 × Allen key
• 4 × Handlebar screws
• 1 × Charger
• 1 × Power cord

Location of Parts

Refer to the pictures 1 and
1. Front Light
2. Rear Brake Lever
3. Hook/Stem Fold Lock Catch
4. Stem Lock Lever
5. Front Wheel
6. Stand
7. Battery Location
8. Foot Pad
9. Handlebar Lock
10. Rear Light
11. Foot Brake
12. Electric Motor
13. Rear Brake
14. Bell
15. Display
16. Throttle
17. Fold Lock Catch (EM-KS2A only)
Display
Refer to the pictures 3 on page 2.
1. Battery level
2. Lights on
3. Gear mode
4. Bluetooth mode (for use with app)
5. Speed unit
6. ODO / TRIP mode indicator
7. ODO / TRIP details
8. Power (this will appear on the display for about 2 seconds after turning on)
9. Speed
10. Light Button
11. Power Button
12. USB Charging Socket
Odo/Trip
Odo will should the total distance covered by the e-scooter; Trip info that
indicates the single driving distance. It is possible to toggle between the
Odo and Trip by short pressing the power-button.
Lights
To turn the front and rear lights on, press the Light Button for a few
seconds. To turn off the lights, press the button for a few seconds.
NOTE: the front and rear lights cannot be controlled independently.
Gears
To change gear, press the light button quickly. Gears will go up then down.
Maximum speed in each gear:
• 1st gear - 6km/h
• 2nd gear - 20km/h
• 3rd gear - 25km/h
The maximum speed for 3rd gear is 25 km/h.
2 on page 1.
Note that these are the maximum speeds which are attainable in each
gear; the e-scooter will not go faster than these speeds in the gear
selected.
Speed
Speed units can be changed in the app.
Cruise Control
Your e-scooter is equipped with a cruise control. To enable this, when
you reach the desired speed hold down the thumb throttle control for 9
seconds. A bleep will sound when the cruise control in engaged. To release
the cruise control, engage the handbrake.
Assembling the Handlebars
• With reference to pictures
handlebars with the supplied Allen key. This only has to be carried
out when the product is un-boxed; the handlebars do not have to be
removed after being attached.
• Insert the handlebars into the handlebar stem as shown in the pictures.
The handlebars have to be orientated as shown. While assembling the
handlebars, be careful not to bend or break any parts.
• Ensure that the screws are not overtightened and that the handlebars
are secure and do not wobble after construction.
• Ensure that the brake cable is not bent or damaged.
Unfolding and Folding the e-scooter
How to unfold?
Refer to the pictures 6 on page 3 unfold the e-scooter.
Press down on the rear fender with one hand and use the other to lift up
the Handlebar Stem so that it is straight, refer to picture
straight it will not move any further. Once locked, use the Fold Lock Lever
to secure in place. This lever must be as close to the Handlebar Stem as
possible when in the lock position. See picture
How to fold?
Refer to the pictures 7 on page 3 fold the e-scooter for storage.
Lift up the Fold Lock Lever as shown in step 1 to release the Handlebar
Stem. Push the Handlebar Stem down as shown in step 2 until it is
touching the Rear Fender. No press down so that it connects with the hook
in the Rear Fender as shown in step 3.
Note that on the EM-KS2A that the Fold Lock Catch is located on
one side of the display and this results in the handlebar stem being
slightly diagonal to the Foot Pad when correctly located.
Using Your e-scooter
Riding
• Before riding ensure that it is safe to do so, the e-scooter is being
operated in accordance with this User Manual. It important that safety
equipment is worn and that the scooter is in good condition.
• If you are using your e-scooter for the fi rst time, practice how to use
it away from public spaces and wear safety equipment. When you are
confi dent to use your e-scooter you can operate near to other people
and vehicles.
To ride your e-scooter safely:
• Make sure that you are wearing suitable safety equipment.
• Power on the e-scooter.
4 and 5 on page 2, assemble the
6 step 3. When
6 step 3 and 4.