Battery And Charger Safety; Product Familiarisation; Intended Use; Unpacking Your Tool - Silverline 991471 Manual De Instrucciones

EN
WARNING: Avoid direct eye contact.
A hazard may exist if you deliberately stare into the beam, please observe
all safety rules as follows:
• The laser shall be used and maintained in accordance with the
manufacturer's instructions
• Do not switch on the laser light until the tool is ready to cut
•
Never aim the beam at any person, and particularly not into the
eyes of any person or animal, or any object other than the
workpiece
• Always ensure the laser beam is aimed at a sturdy workpiece
without reflective surfaces. i.e. wood or rough-coated surfaces are
acceptable. Reflective sheet steel or similar is not suitable for laser
use as the reflective surface could direct the beam back at the
operator
•
Do not change the laser light assembly. Repairs must only be carried
out by the laser manufacturer or an authorised agent. DO NOT
exchange with a different type of laser
Battery and Charger Safety
Use the Battery Charger correctly
• Refer to the section of this manual relating to use of the
Battery Charger (30) before attempting to charge the
Battery (1)
• Do not attempt to use the Battery Charger with any
batteries other than those supplied.
• Keep your Battery Charger clean; foreign objects or dirt may
cause a short or block air vents. Failure to follow these
instructions may cause overheating or fire
•
If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified
persons in order to avoid a hazard
• Examine the Battery Charger regularly for damage,
especially the cord, plug and enclosure. If the Battery
Charger is damaged, it must not be used until it has been
repaired
•
Children should be supervised to ensure that they do not
play with the appliance
WARNING: Do not attempt to recharge non-rechargeable batteries.
Battery Safety
WARNING: Li-ion batteries, if incorrectly used, stored or charged are a
fire, burn and explosion hazard.
• Keep the battery out of reach of children
• Only charge Li-ion batteries designed specifically for this
charger
•
Only use Li-ion batteries provided with this product or
specifically designed to be compatible
• Allow batteries to cool for 15 minutes after charging or
heavy use. Failure to follow these instructions may cause
overheating or fire
•
When not in use batteries should be stored at room
temperature (approximately 20˚C)
•
Ensure battery contacts cannot accidentally short in
storage. Keep batteries clean; foreign objects or dirt may
cause a short. Keep away from other metal objects, for
example paperclips, coins, keys, nails and screws
•
Under abusive conditions, liquid may be ejected from the
battery. This liquid may cause skin irritation or burns. Avoid
contact. If contact accidentally occurs, flush with water. If
liquid contacts eyes, seek medical help
•
Do not open, disassemble, crush, heat above 60°C or
incinerate. Do not dispose of in fire or similar
•
Do not get batteries wet or immerse in water
Product Familiarisation
1. Battery
2. Battery Release
3. Battery Mount
4. Dust Extraction Port
5. Main Handle
6. Switch Safety Lock
7. ON/OFF Switch
8. Auxiliary Handle
9. Parallel Guide Adjustment Knob
10. Parallel Guide Mounting Slots
11. Base Plate
12. Blade Direction Indicator
13. Blade Guard
14. Blade
15. Blade Securing Bolt
16. Blade Securing Flange
17. Guard Retraction Lever
18. Battery Charge Indicator
19. Bevel Angle Scale
20. Guide Notch
21. Bevel Locking Knob
22. Bevel Angle Guide
23. Spindle Lock Button
24. Depth Locking Knob
25. Cutting Depth Guide
26. Depth Guide Scale
27. Dust Port Adaptor
28. Parallel Guide
29. Hex Key
30. Battery Charger
31. Red LED
32. Green LED
33. Charger Terminals
Intended Use
Hand-held, battery-powered, circular saw for cross, rip and bevel cutting of
hard and softwood timber, and wood-based sheet material. Suitable for
creating pocket/plunge cuts when used carefully by a skilled operator.
The tool must ONLY be used for its intended purpose. Any use other than
those mentioned in this manual will be considered a case of misuse. The
operator, and not the manufacturer, shall be liable for any damage or
injury resulting from such cases of misuse. The manufacturer shall not be
liable for any modifications made to the tool, nor for any damage resulting
from such modifications.
Unpacking Your Tool
•
Carefully unpack and inspect your product. Fully familiarise
yourself with all its features and functions
•
Ensure all parts of the product are present and in good
condition
• If any parts are missing or damaged, have such parts
replaced before attempting to use this product
Before Use
WARNING: ALWAYS remove the battery before attaching or changing
any accessories, or making any adjustments.
Removing the Battery
To remove the Battery (1), press the Battery Release (2) and slide the
Battery out of the Battery Mount (3) (Fig. I (a-b))
silverlinetools.com
Original Instructions
10