Technical Data - Bosch AHM 30 Manual Original

OBJ_BUCH-1705-002.book Page 9 Thursday, December 15, 2016 9:27 AM

Technical Data

Cylinder Mower AHM 30
Article number 3 600 H86 003 3 600 H86 101 3 600 H86 002 3 600 H86 102 3 600 H86 000 3 600 H86 104
Blade width cm
No of Cylinder
Blades
15 – 50
Height of cut mm
Grassbox
Weight accord-
ing to EPTA-
Procedure
01:2014 kg
Intended Use
The garden product is intended for domestic lawnmowing.
The garden product is intended for lawn mowing at ground
level.
Delivery Scope
Carefully remove the garden product from its packaging and
check if the following parts are complete:
– Lawnmower
– Handle bottom
– Handle top
– Handle Centres (2x)
– Nuts (6 x)
– Screwdriving (6 x)
– Grassbox (AHM 30 G/AHM 38 G)
– Grasscatcher hooks (2 x) (AHM 30 G/AHM 38 G)
– Grasscatcher nuts (2 x) (AHM 30 G/AHM 38 G)
– Washers (2x) (AHM 30 G/AHM 38 G)
– Grasscatcher bolts (2 x) (AHM 30 G/AHM 38 G)
– Operating instructions
When parts are missing or damaged, please contact your
dealer.
Product Features
The numbering of the garden product features refers to the il-
lustration of the garden product on the graphics page.
1 Handle top
2 Handle centres
3 Handle bottom
4 Grassbox*
5 Grasscatcher nut*
6 Grasscatcher hook*
7 Washer*
8 Grasscatcher bolt*
9 Adjustment knob
10 Wing nut
11 Cutting cylinder
Bosch Power Tools
AHM 38 AHM 30 C
30 38
5 5
15 – 50
15 – 43
– –
5.9 6.7
12 Blade
13 Roller bracket
* The accessories illustrated or described are not included as
standard delivery.
Assembly
Handle assembly (see figures A – B)
Attach bottom handle 3 to the mower.
Assemble the top handle 1 to the handle centres 2 and fit to
handle bottom 3.
Grassbox assembly
(AHM 30 G/AHM 38 G)
Attach grasscatcher hooks 6 to mower using bolts 8, washers
7 and nuts 5 and fit grasscatcher 4.
Adjusting the Cutting Height
Coarse (see figure E)
The roller brackets 13 should be set in one of three positions
according to the type of lawn: I for high range for bumpy
lawns, II for medium range for average lawns and III fore low
range for reasonably flat lawns. You should only need to make
this adjustment once, thereafter use the „Fine" adjustment to
cut longer or shorter grass.
To change the height of cut:
– Remove the wingnut 10 and bolt.
– Reposition the bolt for required height of cut.
– Refit wingnut 10.
Fine (X) (see figure F)
Slacken wing nut 10 on both sides of the mower. Move both
roller brackets 13 equally to the required height of cut.
Mowing (see figure G)
For best mowing results, begin mowing from the edge of the
lawn in a forwards direction, forming an "L" pattern. Turn
around at the end of the length, slightly overlapping the previ-
ous swath.
AHM 38 C AHM 30 G
30 38
5 5
15 – 50
15 – 43
– –
6.6 7.5
F 016 L81 514 | (08.08.19)
English | 9
AHM 38 G
30 38
5
5
15 – 50
● ●
6.8 7.7