Asist AE3KS25DN Instrucciones De Uso página 43

not grind by using the side surfaces of the grinding
wheel, as excessive pressure on the side of the wheel
could damage it.
Troubleshooting
Even if your new bench grinder is very easy to use
and you still have problems, check the grinder as
follows:
1. The grinder does not start: Check that it is connect-
ed to the mains; check the voltage level with an elec-
trical tester or other electrical device. networks; check
the connections of the socket; check and tighten
loose connections; check fuse; in case of suspicion,
replace with a new one with the correct value.
2. The disc shakes or vibrates: Check that the lock
nut is tightened. Check that the disc is mounted
on the shaft and on the shim correctly. If excessive
pressure is applied or the blade is „stuck", it may be
damaged and cause vibration. As soon as there is
any sign of damage to the blade, remove it immedi-
ately and replace it with a new blade.
3. The blade leaves a rough surface. Excessive pres-
sure on the disc can cause incorrect surface finish. If
you are working with aluminum or similar soft alloys,
the blade will clog very easily or then grind effectively.
There are no user serviceable parts inside this bench
grinder. In case of problems, take the grinder to an
authorized service center.
CLEANING AND MAINTENANCE
! Before cleaning and maintenance, always unplug
the grinder power cord.
The machine does not require any special mainte-
nance.
Do not clean any part of the machine with a hard,
sharp or rough object.
Long-term storage
decommissioning
Do not store the grinder in a place where the tem-
perature is high.
If possible, store the machine in a place with a con-
stant temperature and humidity.
SPECIFICATIONS
Input voltage 230 V
Input frequency 50 Hz
Power consumption 250W S2 30 min.
Idle speed 2950 rpm
Grinding wheel diameter Ø150mm
Inner diameter of the disc Ø12.7 mm
Max. thickness no. wheels 16 mm
Weight 5 kg
Protection class I.
Sound pressure level measured according to EN
60745:
LpA (sound pressure) 72,1dB (A) KpA=3
LWA (sound power) 83,1 dB (A) KwA=3
Take appropriate measures to protect your hearing!
Wear hearing protection whenever the sound pressure
exceeds the level of 80 dB (A).
Weighted effective acceleration according to EN
60745:
<2,5 m/s2 K=1.5
Caution: The vibration level may vary during power
tool operation from the declared value depending on
the way the power tool is used and depending on the
following conditions: Method of power tool use and
type of material being cut or drilled, conditions of the
power tool and method of its maintenance, appro-
priateness of the used accessories and ensuring its
sharpness and good conditions, the strength of handle
gripping, use of anti-vibration equipment, suitability of
the power tool for the purpose for which it has been
designed and compliance with workflows according to
manufacturer's instructions.
If this power tool is used in an inappropriate manner, a
hand/shoulder vibration syndrome may appear.
Caution: For clarification, it is necessary to consider
the level of vibrations in specific conditions of use in all
operating modes, e.g. the time when the power tool is
switched off except for the operation time, and when
it idles, i.e. performs no work. This may substantially
decrease the exposition level during the whole operat-
ing cycle.
Minimize the risk of vibrations, use sharp chisels, drill
and blades.
Keepthe power toolin compliancewith theseinstruc-
tions and provide for its proper lubrication.
When using the power tool regularly, invest into anti-
vibration equipment.
Do not use the power tool under temperatures lower
than 10°C. Plan your project containing work with the
power tool producing high vibrations carefully and
spread it over more days.
Subject to changes.
ENVirONmENTaL PrOTECTiONWaSTE ma-
NagEmENT
Power tools, accessories and packaging should be
provided for recycling and not to harm the environment.
Do not dispose of power tools into household waste!
According to Directive 2012/19/EU of the European
Parliament and of the Council on waste electrical and
electronic equipment (WEEE) and its approximation
in national laws, unfit power tools must be handed
over at the point of purchase of similar equipment, or
in available collection points designated for collection
and disposal of power tools. Such disposed power
tools will be collected, disassembled and delivered for
environment-friendly recycling.
WarraNTY
43