Hubbell iDevices IDEVZ01DW Manual

FCC/IC
En
This device complies with Part 15 of the FCC and Industry Canada license-exempt RSS
standards. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
FCC NOTE: The manufacturer is not responsible for any radio or TV interference caused
by unauthorized modifications to this equipment. Such modifications could void the user's
authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy, and if not installed and used in accordance with
the instructions may cause harmful interference to radio communications. However, there is no
guarantee interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from which
the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help
Important note: To comply with the FCC RF exposure compliance requirements, no change
to the antenna or the device is permitted. Any change to the antenna or the device could result
in the device exceeding the RF exposure requirements and void user's authority to operate
the device.
Fr
Cet appareil est conforme au paragraphe 15 des normes FCC et au CNR pour les appareils
exempts de licence d'Industrie Canada. Son utilisation est sujette aux deux conditions
suivantes : (1) cet appareil ne doit pas occasionner de brouillage préjudiciable et (2) cet
appareil doit accepter toutes les interférences reçues, notamment les interférences qui peuvent
provoquer un fonctionnement non désiré.
NOTE DE LA FCC : Le fabricant n'est pas responsable des interférences sur les fréquences
radioélectriques ou télévisuelles pouvant être causées par des modifications non autorisées de
ce matériel. De telles modifications peuvent annuler le droit de l'utilisateur à utiliser cet appareil.
REMARQUE : Cet appareil a été testé et certifié conforme aux limites relatives aux appareils
numériques de catégorie B définies dans le paragraphe 15 des normes FCC. Ces limites
ont été définies afin de fournir une protection raisonnable contre le brouillage préjudiciable
en milieu résidentiel. Cet appareil produit, utilise et peut émettre des ondes de fréquence
radio et, s'il n'est pas installé et utilisé conformément aux instructions, il peut provoquer un
brouillage préjudiciable aux communications radio. Il n'existe toutefois aucune garantie que
des interférences ne se produiront pas au sein d'une installation donnée. Si cet appareil
occasionne un brouillage préjudiciable à la réception radiophonique ou télévisuelle, il suffit
d'allumer et d'éteindre l'appareil pour déterminer sa responsabilité. Nous encourageons
l'utilisateur à essayer de corriger ces interférences en appliquant une ou plusieurs des mesures
suivantes :
— Réorienter ou déplacer l'antenne de réception.
— Augmenter la distance entre l'appareil et le récepteur.
— Brancher l'appareil à une prise secteur différente de celle du récepteur.
— Consulter le revendeur ou un technicien spécialisé en postes radio ou téléviseurs.
Remarque importante : Pour se conformer aux exigences de conformité de la FCC
concernant l'exposition aux RF, aucune modification apportée à l'antenne ou au dispositif n'est
autorisée. Toute modification apportée à l'antenne ou au dispositif pourrait faire en sorte que le
dispositif dépasse les exigences d'exposition aux RF et pourrait annuler le droit de l'utilisateur
à utiliser ce dispositif.
Es
Este dispositivo cumple con las Especificaciones del apartado 15 de las normas de la FCC
y con las especificaciones de las normas radioeléctricas (RSS) del Ministerio de Industria
de Canadá aplicables a aparatos exentos de licencia. El funcionamiento está sujeto a las
siguientes dos condiciones: (1) este dispositivo no debe provocar interferencia perjudicial, y (2)
este dispositivo debe aceptar toda interferencia que reciba, incluso la que pudiera causar un
funcionamiento no deseado.
NOTA DE LA FCC: El fabricante no se hace responsable de ninguna interferencia de radio
o TV ocasionada por modificaciones no autorizadas efectuadas a este equipo. Dichas
modificaciones podrían anular la autoridad del usuario para utilizar el equipo.
NOTA: Este equipo ha sido probado y cumple con los límites para aparatos digitales de
Clase B, de conformidad con el apartado 15 de las normas de la FCC. Estos límites están
diseñados para proveer protección razonable contra interferencias perjudiciales en una
instalación residencial. Este equipo genera, usa y puede irradiar energía de radiofrecuencias
y, si no se instala y usa según las instrucciones, puede provocar interferencia perjudicial a las
radiocomunicaciones. No obstante, no hay garantías de que no ocurrirá interferencia en una
instalación en particular. Si este equipo provoca interferencia perjudicial a la recepción de radio
o televisión, lo que puede determinarse encendiendo y apagando el equipo, se recomienda
que el usuario intente corregir la
interferencia por medio de la implementación de una o más de las siguientes medidas:
— Reorientar o reubicar la antena receptora.
— Incrementar la separación entre el equipo y el receptor.
— Conectar el equipo a un tomacorriente de un circuito diferente del circuito al que está
conectado el receptor.
— Consultar al distribuidor o a un técnico con experiencia en radio/televisión para
solicitar asistencia.
Nota importante: Para cumplir con los requisitos de cumplimiento de exposición de
radiofrecuencia de la FCC, no se permiten cambios a la antena o el dispositivo. Cualquier
cambio a la antena o dispositivo podría hacer que el dispositivo supere los requerimientos de
exposición de radiofrecuencia y anular la autoridad del usuario para operar el dispositivo.
Responsible Party - US Contact Information | Parte responsable - Información de
contacto de los Estados Unidos | Partie responsable - Coordonnées des États-Unis
IDEVZ01DW:
FCC ID— U2ZZW4008 | IC: 6924A-ZW4008
Wiring Devices-Kellems Hubbell Incorporated | Model: IDEVZ01DW
(Delaware) Shelton, CT 06484 | 1-800-288-6000
CAN ICES-3(B)/NMB-3(B)
All brand names shown are trademarks of their MADE IN CHINA/FABRIQUÉ EN CHINE/
respective owners. HECHO EN CHINA
Tous les noms de marque illustrés sont des DISTRIBUTED BY
marques de commerce de leurs propriétaires WIRING DEVICES-KELLEMS
respectifs. HUBBELL INCORPORATED
(DELAWARE)
Todas las marcas que aparecen aquí
son marcas registradas de sus respectivos dueños. SHELTON, CT 06484.
©Hubbell | IDEVZ01DW | 05/17/21 v1
1.
Tools You Will Need
IMPORTANT!
The fixture controlled by the Z-Wave In-Wall Smart Switch must not
exceed 960W incandescent, 1800W (15A) resistive or 1/2HP motor. The
switch is designed only for use with permanently installed fixtures.
Getting to know your new Z-Wave device
• Turn ON/OFF manually or remotely via the Z-Wave controller
• Can be included in multiple groups and scenes
• May be used in single-pole installation or with up to four add-on switches (model
46560) in 3-way or 4-way wiring configurations
• Compatible with all LED/CFL and incandescent bulbs
• Auto line/load detection
• Interchangeable paddle switch — white & light almond paddle in package
• Uses a standard, rocker-style wallplate for single-gang installations
(wallplate not included)
• Blue LED indicates switch location in a dark room
• Z-Wave certified for simple pairing and integrated home automation
• Screw terminal installation — requires wiring connections for line (hot), load,
neutral and ground. Traveler wire required for 3-way or 4-way installation
• This Z-Wave device has advanced features that allow you to customize your
experience. These features can only be adjusted by a Z-Wave enabled controller
that supports the Z-Wave configuration command class. For a complete list of
adjustable configurations, visit www.www.hubbell-wiring.com
2.
A
D
B
F
G
C
E
A. Ground (Green/Bare) F. Top rocker — press &
B. Line or Load (Black) release to turn switch on
C. Line or Load (Black) G. Bottom rocker — press &
D. Traveler (Red/Other) release to turn switch off
E. Neutral (White)
MANUAL • MANUEL • MANUAL
In-Wall
Smart Switch
Montage mural
intelligent enfichable
Interruptor
inalàmbrico
inteligente
Convert any smart control* to a multi-location switch
*For a list of compatible devices, visit www.hubbell-wiring.com
Smart Control Add-on Switches
To purchase an add-on switch or for more details,
visit www.hubbell-wiring.com.
Multiple Paddle Colors Available
www.hubbell-wiring.com
Purchase additional items at
www.hubbell-wiring.com or visit your local retailer.
In-Wall In-Wall In-Wall
Tamper-Resistant Smart Dimmer Add-on Switch
Smart Outlet
3.
OR
OR
WARNING — SHOCK HAZARD
Turn OFF the power to the branch circuit for the switch and lighting fixture at the
service panel. All wiring connections must be made with the POWER OFF to avoid
personal injury and/or damage to the switch.
This device is intended for installation in accordance with the National Electric
Code and local regulations in the United States or the Canadian Electrical Code
and local regulations in Canada. This device is to be installed by a qualified
electrician following these instructions.
Multi-switch wiring
For 3-way installations, please refer to add-on switch (model 46560) manual
Single-switch wiring
Before installation, you may wish to change the paddle color to match your wallplate or
décor. Please proceed to section 5.
1. Shut off power to the circuit at circuit breaker or fuse box.
IMPORTANT! Verify power is OFF to switch box before continuing.
2. Remove wallplate.
3. Remove the switch mounting screws.
4. Carefully remove the switch from the switch box. DO NOT disconnect the wires.
4.
Adding your device to a Z-Wave network To remove and reset the device
1. Follow the instructions for your Z-Wave certified
1. Follow the instructions for your Z-Wave certified controller
controller to add a device to the Z-Wave network.
2. Once the controller is ready to add your device, press the
2. Once the controller is ready to remove your device, press
top or bottom of the wireless smart switch (rocker).
You have complete control to turn your fixture
To return your switch to factory defaults
ON/OFF according to groups, scenes, schedules and
1. Quickly press ON (top) button three times, then, immediately
interactive automations programmed by your controller.
If your Z-Wave certified controller features remote access,
you can control your fixture from your mobile devices.
Note: This should only be used if your network's primary controller is
If prompted by the controller to enter the S2 security code, refer to the QR
missing or otherwise inoperable.
code/security number on the side of the box or the QR code label on the
product (see Figure 1). Enter the 5-digit code.
Figure 1
NOTE: SmartStart enabled products can be added into a Z-Wave network by
scanning the QR code on the product with a controller providing SmartStart
inclusion. No further action is required and the SmartStart product will be added
automatically within 10 minutes of being switched on in the network vicinity.
DO NOT RETURN THIS
PRODUCT TO THE STORE
STOP
NE RETOURNEZ PAS
CE PRODUIT AU MAGASIN
NO DEVUELVA ESTE
PRODUCTO A LA TIENDA
Questions? Contact our U.S.-based Consumer Care at 1-800-288-6000.
For the most up-to-date product support, accessories, electronic (PDF) format
manuals and more, visit www.hubbell-wiring.com.
• No user-serviceable parts in this unit.
Des questions? Contactez notre Service Consommateurs basé aux États-Unis
au 1-800-288-6000.
Pour le soutien relatif aux produits le plus à jour, les accessoires, les manuels en
IDEVZ01DW format électronique (PDF) et plus encore, visitez le site
www.hubbell-wiring.com.
• Aucune des pièces de ce dispositif ne peut être réparée par l'utilisateur.
Preguntas? Póngase en contacto con nuestro Servicio de Atención al
Consumidor con sede en EE. UU. Al 1-800-288-6000.
Para recibir el soporte técnico más actualizado sobre productos, accesorios,
manuales en formato digital (PDF), entre otros, visite www.hubbell-wiring.com.
• Esta unidad no contiene piezas que el usuario pueda reparar.
WARNING
RISK OF FIRE RIESGO DE INCENDIO
RISK OF ELECTRICAL SHOCK RIESGO DE DESCARGA ELÉCTRICA
RISK OF BURNS RIESGO DE QUEMADURAS
CONTROLLING APPLIANCES CONTROL DE EQUIPOS
CAUTION: ELECTRODOMÉSTICOS
PRECAUCIÓN:
• D O NOT EXCEED RATINGS
• N O SUPERE LOS VALORES NOMINALES
• D O NOT USE TO CONTROL ANY DEVICE WHERE
UNINTENDED OPERATION COULD CAUSE UNSAFE ELÉCTRICOS
CONDITIONS (HEAT LAMP , SUN LAMP , ETC.)
• N O USAR PARA CONTROLAR DISPOSITIVOS
EN LOS QUE EL FUNCIONAMIENTO NO
• D O NOT USE TO CONTROL RECEPTACLES
INTENCIONADO PODRÍA PROVOCAR
• F OR INDOOR USE ONLY
SITUACIONES PELIGROSAS (LÁMPARAS DE
CALEFACCIÓN, LÁMPARAS SOLARES, ETC.)
• N O UTILICE PARA CONTROLAR
AVERTISSEMENT
TOMACORRIENTES.
• U SE SOLAMENTE EN INTERIORES
RISQUE D'INCENDIE
RISQUE DE CHOC ÉLECTRIQUE
RISQUE DE BRÛLURES
COMMANDE DES APPAREILS
ATTENTION :
NOT FOR USE WITH MEDICAL OR
• N E PAS DÉPASSER LES CARACTÉRISTIQUES
LIFE-SUPPORT EQUIPMENT
NOMINALES
Z-WAVE ENABLED DEVICES SHOULD NEVER BE
• N E PAS UTILISER POUR COMMANDER
USED TO SUPPLY POWER TO OR CONTROL THE
DES APPAREILS POUR LESQUELS UN
ON/OFF STATUS OF MEDICAL OR LIFE-SUPPORT
FONCTIONNEMENT IMPRÉVU POURRAIT
EQUIPMENT.
ENTRAÎNER DES CONDITIONS DANGEREUSES
(LAMPE À RAYONS INFRAROUGES, LAMPE
SOLAIRE, ETC.) NE PAS UTILISER AVEC UN ÉQUIPEMENT
MÉDICAL OU DE SURVIE
• N E PAS UTILISER POUR COMMANDER LES PRISES
DE COURANT LES DISPOSITIFS COMPATIBLES AVEC LA
TECHNOLOGIE Z-WAVE NE DEVRAIENT
• P OUR UTILISATION INTÉRIEURE UNIQUEMENT
JAMAIS ÊTRE UTILISÉS POUR ALIMENTER OU
COMMANDER LA MISE EN MARCHE OU L'ARRÊT DE
L'ÉQUIPEMENT MÉDICAL OU DE SURVIE.
SE PROHÍBE SU EMPLEO EN
EQUIPO MÉDICO O EQUIPO PARA EL
MANTENIMIENTO DE LAS FUNCIONES
VITALES
LOS DISPOSITIVOS Z-WAVE NUNCA SE DEBEN
USAR PARA SUMINISTRAR ENERGÍA ELÉCTRICA
AL EQUIPO MÉDICO O AL EQUIPO PARA EL
MANTENIMIENTO DE FUNCIONES VITALES, NI
PARA CONTROLAR EL ESTADO DE ENCENDIDO O
APAGADO DE DICHOS EQUIPOS.
Insert wires into holes, do not wrap wires
Out to Light (Load)
around screws.
Do not remove screws.
B
D
E
A
C
From Breaker Box
There are up to five screw terminals on the switch; these are marked:
A. GROUND — Green/Bare
B. LINE OR LOAD — Black (connected to power or lighting)
C. LINE OR LOAD — Black (connected to power or lighting)
D. TRAVELER — Red/Other (only in 3-way installations)
E. NEUTRAL — White
Match these screw terminals to the wires connected to the existing switch.
5. Disconnect the wires from the existing switch. Label wires according to
the previous terminal connection.
Observe important wiring information
IMPORTANT! This switch is rated for and intended to only be used with copper
wire.
Wire gauge requirements
Use 14AWG or larger wires suitable for at least 80° C for supplying line (hot), load,
neutral, ground and traveler connections.
Wire strip length
For attachment using the enclosure's holes, strip insulation 5/8in. (16mm).
UL specifies the tightening torque for the screws is 14Kgf-cm (12lbf-in).
1. Connect the green or bare copper ground wire to the GROUND terminal.
2. Connect the black wire from the light to either LINE/LOAD terminal.
3. Connect the black wire from the electrical service panel (hot) to the remaining
LINE/LOAD terminal.
4. Connect the white wire to the NEUTRAL terminal (use a jumper wire if needed).
5.
to remove a device from the Z-Wave network.
the top or bottom of the wireless smart switch (rocker).
press the OFF (bottom) button three times. The LED will
flash ON/OFF five times when completed successfully.
DSK :
Z-WAVE DSK
XXXXX
-25651-22671
-26939-47599
-19612-25872
PIN: XXXXX
-47752
Wiring Devices-Kellems
WARRANTY
Wiring Devices-Kellems warrants this product to be free from manufacturing defects for two years from the original date
of consumer purchase. This warranty is limited to the repair or replacement of this product only and does not extend to
consequential or incidental damage to other products that may be used with this product. This warranty is in lieu of all
other warranties, expressed or implied. Some states do not allow limitations on how long an implied warranty lasts or
permit the exclusion or limitation of incidental or consequential damage, so the above limitations may not apply to you.
This warranty gives you specific rights, and you may also have other rights which vary from state to state. Please contact
our U.S.-based Consumer Care at 1-800-288-6000 if the unit should prove defective within the warranty period.
GARANTIE
Wiring Devices-Kellems garantit que ce produit est exempt de tout défaut de fabrication pour une période de deux
ans à compter de la date de l'achat original par l'acheteur. Cette garantie se limite exclusivement à la réparation ou au
remplacement de ce produit et n'est pas applicable aux dommages indirects ou accessoires survenus sur d'autres
produits utilisés avec ce produit. Cette garantie se substitue à toute autre garantie expresse ou implicite. Certains États
ne permettent pas de restrictions quant à la durée d'une garantie implicite ou permettent l'exclusion ou la limitation des
dommages indirects et accessoires; il se peut, par conséquent, que cette garantie ne s'applique pas dans votre cas.
Cette garantie vous confère des droits juridiques précis; vous pouvez jouir d'autres droits qui peuvent varier d'un État à
l'autre. Contactez notre Service Consommateurs basé aux États-Unis au 1-800-288-6000 si l'appareil s'avère défaillant
au cours de la période de garantie.
GARANTÍA
Wiring Devices-Kellems garantiza que este producto está libre de defectos de fabricación durante un periodo de dos
años a partir de la fecha original de compra por parte del consumidor. Esta garantía se limita a la reparación o sustitución
de este producto solamente y no se extiende a daños derivados o accidentales causados a otros productos que se
usen con esta unidad. Esa garantía remplaza a todas las demás garantías expresas o implícitas. Algunos estados no
autorizan limitaciones en cuanto a la duración de una garantía implícita ni permiten la exclusión o limitación por daños
accidentales o derivados; por lo tanto, puede que las anteriores limitaciones no apliquen en su caso. Esta garantía le
da a usted derechos específicos, y otros que usted puede tener y que varían según el estado en el que usted reside.
Si la unidad resultare defectuosa dentro del periodo de garantía, comuníquese con nuestro Servicio de Atención al
Consumidor con sede en EE. UU. Al 1-800-288-6000.
Wiring Devices-Kellems Hubbell Incorporated
(Delaware) Shelton CT,06484.
ADVERTENCIA
SPECIFICATIONS
IDEVZ01DW
Power: 120VAC, 60Hz
Signal (frequency): 908.4/916MHz
Maximum loads: 960W incandescent, 1/2HP motor or 1800W (15A) resistive
Range: Up to 150ft. line of sight between the wireless controller and the closest Z-Wave receiver module
Operating temperature range: 32-104° F (0-40° C)
Type 1 enclosure, independently mounted (vertical position only), operating control: type 1.c action,
pollution degree (2), impulse voltage (2500V), software class A
For indoor use only
Specifications subject to change without notice due to continuing product improvement
SPÉCIFICATIONS
IDEVZ01DW
Tension : 120VCA, 60Hz
Signal (fréquence) : 908.4/916MHz
Charges maximales : 960W incandescent, moteur de 1/2HP ou résistance de 1800W (15A)
Portée : Distance à vue entre la télécommande et le module de réception Z-Wave le plus proche allant
jusqu'à 150 pi (45.7m)
Plage de températures de fonctionnement: De 0 à 40° C (de 32 à 104° F)
Boîtier de type 1, monté indépendamment (position verticale seulement), intervention de type 1.c
commande de fonctionnement, degré de pollution (2), tension de choc de (2500V), logiciel de classe A
Utilisation intérieure uniquement
En raison d'améliorations continues du produit, les spécifications peuvent faire l'objet de changements
sans préavis
ESPECIFICACIONES
IDEVZ01DW
Energía: 120VCA, 60Hz
Señal (frecuencia): 908.4/916MHz
Cargas máximas: 960W incandescente, 1/2HP motor o 1800W (15A) resistiva
Alcance: Hasta 150 pies (45.7m) en línea de visibilidad directa entre el control inalámbrico y el módulo
receptor Z-Wave más cercano
Rango de temperatura de funcionamiento: 0-40° C (32-104° F)
Recinto de tipo 1, independientemente montado (solo en posición vertical), control de operación: acción
tipo 1.c, grado de contaminación (2), voltaje de impulso (2500V), software de clase A
Para uso en espacios interiores solamente
Especificaciones sujetas a cambio sin aviso debido a continuas mejoras del producto
Out to Light (Load)
B
A
D
E
C
From Breaker Box
Note: The traveler terminal is only used for 3-way or 4-way wiring and should
remain unused if the switch is being installed in a 2-way system (one switch &
one load).
5. Insert switch into the switch box being careful not to pinch or crush wires.
6. Switch must be independently mounted (vertical position only).
7. Secure the switch to the box using the supplied screws.
8. Mount the wallplate.
9. Reapply power to the circuit at fuse box or circuit breaker and test the system.
Basic operation
The connected fixture can be turned ON/OFF in two ways:
1. Manually from the front panel of the switch
2. Remotely with a Z-Wave controller
Manual control
The front panel rocker switch allows the user to turn ON/OFF the connected fixture.
1. To turn the connected fixture ON, press and release the top of the rocker.
2. To turn the connected fixture OFF, press and release the bottom of the rocker.
Cycle LED light
The LED below the switch acts as a guide light or status indicator.
How to cycle through options: Press up three times and down once quickly.
1. LED is ON when the load is OFF (guide light in the dark) (default)
2. LED is ON when the load is ON (indicates the switch is ON)
3. LED is always OFF
4. LED is always ON (illuminates switch in the dark)
Changing paddle color
This step is optional. Before installation,
you may want to change the color of the
2.
paddle to match your wallplate or décor.
1. Lift the air gap tab at the base of the
paddle.
2. Push side tabs in on one side and then
the other to release paddle. Lift the
cover up and off.
3. Simply put the new paddle onto the
switch by inserting the air gap and side
1.
tabs and snapping securely into place.
Once this step has been completed,
return to section 3.
Z-WAVE INTEROPERABILITY
This product can be included and operated in any Z-Wave network with other Z-Wave certified
devices from other manufacturers and/or other applications. All non-battery operated nodes
within the network will act as repeaters regardless of vendor to increase reliability of the
network.
This device supports Association Command Class (3 Groups)
• Association Group 1 supports Lifeline, Binary Switch Report
• Association Group 2 supports Basic Set and is controlled by pressing the ON/OFF button with the local load
• Association Group 3 supports Basic Set and is controlled by double pressing the ON/OFF button
• Each Association Group supports 5 total nodes
The Hubbell Add-on Switch is required
for multi-switch 3-way or 4-way
installations.
Connecting the traveler terminal of this
switch to a standard, non-Hubbell switch
will cause damage or result in improper
function. If this switch is part of a 3-way
or 4-way multi-switch installation, do not
connect the traveler wire or apply power
until Hubbell Add-on Switches are
correctly installed. For more information
on 3-way or 4-way installations, view
the manual or quick-start guide for the
Hubbell Add-on Switch.