Audizio REIMS Manual De Instrucciones página 6

The device can be muted by pressing the [MUTE] button on the remote control. Press again to restore the volume.
1. Press the [STANDBY] button on main unit or remote control to turn on the unit.
2. Press the [MODE] button on main unit or remote control to select FM mode.
3. To automatically tune to the next available radio station, press and hold the [
control for 1-2 seconds until SCAN appears on the display, then release the button. The tuner will stop scanning when it
receives the next broadcasting station of adequate signal strength.
4. Press the volume control on main unit or remote control to adjust the volume to the desired level.
5. To manually tune to a specific radio station, tap the [
Use the manual tuning method to tune in weaker stations that are bypassed during automatic tuning.
FM & FM-stereo reception
When listening to the FM radio, press [ST./MONO] on the main unit to switch between stereo mode and mono mode. The FM
stereo icon "ST" will appear on the display when in stereo mode. It is preferable to receive the program in mono when you
are receiving a weak station.
For best possible reception:
The receiver has a build-in FM wire antenna exiting from the back of the cabinet. This wire should be totally unwrapped and
fully extended for the best reception.
1. Press the [STANDBY] button on main unit or remote control to turn on the unit.
2. Press the [MODE] button on main unit or remote control to select FM radio mode.
3. Tune to the desired radio station either "manually" or "automatically".
4. Tap the [MEM.] button on the remote control, the next available preset memory number will flash on the LCD display.
(Note:"P01" will blink in the display if you are programming preset for first time)
5. Press the [PRESET+] or [PRESET-] button on remote control to select the preset number you want to assign the station to.
6. Press the [MEM.] button on remote control to confirm the setting.
Repeat above steps 3 - 6 to preset up to 20 FM stations.
In radio mode, recall the pre-set channels/stations by pressing [PRESET+] or [PRESET-] on remote control.
1. Press the [STANDBY] button on the remote control or main unit to power the device.
2. Press [MODE] on the main unit or remote control repeatedly to enter CD mode.
3. Open the CD tray by pressing at the "OPEN/CLOSE" mark on the CD door, load a CD with the label side facing upward and
close the CD tray.
4. Playback will start from track 1 once the player has finished reading. The play indicator will appear on the LCD display.
5. While playing, press the [PLAY/PAUSE] button to pause, the pause indicator will appear on the LCD display. Press the
[PLAY/PAUSE] button again to resume playing.
6. Adjust the volume using the [VOLUME] buttons.
1. Press [MODE] on the main unit or remote control, and load an MP3/WMA disc.
2. Press [FOLDER+] or [FOLDER-] to select the desired playback folder.
3. Select the desired file to be played by pressing the [SKIP FORWARD] or [SKIP BACKWARD] button.
4. Press the [PLAY/PAUSE] button. Playback will start and file name will be displayed.
In case of playback while under folder mode, press [FOLDER+] or [FOLDER-] and the folder can be selected even though it is
in playback/pause mode. It will continue playback/pause mode in the 1st track of the selected folder.
Single track
When the [REPEAT] button is pressed once, the repeat indicator
will be played repeatedly.
All
When the [REPEAT] button is pressed twice, the repeat indicator
be played continuously.
Random play
Press [REPEAT] three times to enter random play mode. "RAND" will appear on the display.
Press [REPEAT] again to stop random play ("RAND" will no longer show on the display). The unit will now only play the intro
part of every track. Press [REPEAT] again to return to regular playing.
During pause or play, press [SKIP FORWARD] or [SKIP BACKWARD] once to go to the next or previous track or return to the
start of the current track. Hold [SKIP FORWARD] or [SKIP BACKWARD] to search/scan forwards or backwards within the
current track.
] or [
] or [ ] button on either main unit or remote control repeatedly.
will appear and flash on the display. The current track
will appear on the display. The whole disc/folder will
6
] button on main unit or remote