Publicidad
Idiomas disponibles
Idiomas disponibles
English
CAUTION
When the battery charger has been continuously used,
the battery charger will be heated, thus constituting
the cause of the failures. Once the charging has been
completed, give 15 minutes rest until the next charging.
4. Disconnect the charger's power cord from the
receptacle.
5. Hold the charger fi rmly and pull out the battery.
NOTE
Be sure to pull out the battery from the charger after use,
and then keep it.
Regarding electric discharge in case of new batteries,
etc.
As the internal chemical substance of new batteries and
batteries that have not been used for an extended period
is not activated, the electric discharge might be low when
using them the fi rst and second time. This is a temporary
phenomenon, and normal time required for recharging
will be restored by recharging the batteries 2–3 times.
How to make the batteries perform longer.
(1) Recharge the batteries before they become completely
exhausted.
When you feel that the power of the tool becomes
weaker, stop using the tool and recharge its battery. If
you continue to use the tool and exhaust the electric
current, the battery may be damaged and its life will
become shorter.
(2) Avoid recharging at high temperatures.
A rechargeable battery will be hot immediately after
use. If such a battery is recharged immediately after
use, its internal chemical substance will deteriorate, and
the battery life will be shortened. Leave the battery and
recharge it after it has cooled for a while.
CAUTION
○ If the battery is charged while it is heated because it has
been left for a long time in a location subject to direct
sunlight or because the battery has just been used, the
pilot lamp of the charger lights for 1 second, does not
light for 0.5 seconds (off for 0.5 seconds). In such a case,
fi rst let the battery cool, then start charging.
○ When the pilot lamp fl ickers (at 0.2-second intervals),
check for and take out any foreign objects in the charger's
battery connector. If there are no foreign objects, it is
probable that the battery or charger is malfunctioning.
Take it to your authorized Service Center.
MOUNTING AND OPERATION
Action
Removing and inserting the battery
Charging
Changing bit*
1
Selection operating mode / Switch
operation*
2
Mounting and removing the hook
How to use the LED light*
Setting the direction of rotation,
engaging the transporting safety
device (switch-on lock) *
Working with stopper*
5
Figure
3
4
5
6
7
8
3
9
4
10
Remaining battery indicator*
(on tool body)
Remaining battery indicator
(on battery)
Selecting accessories
*1 Changing bit
WARNING
Prevent inadvertent starting: Set manual mode and
remove battery pack from the tool before performing any
retooling.
Inserting and removing the bit:
Remove the stopper.
Insert: Insert the bit in the magnetic bit holder.
Remove: Pull the bit from the magnetic bit holder using
pliers.
Attach the stopper again:
turn and engage in position when mounted.
NOTE
The magnetic bit holder may be removed from the
spindle if the sleeve is pulled back.
*2 Selection operating mode, switch on / off
Set the required operating mode on the dial.
NOTE
When the motor is running, the spindle does not start
until the spindle is pushed in.
Manual mode
Switch on: press the trigger switch. Press in the trigger to
increase the rotational speed.
To switch off release the trigger switch.
Automatic mode
The tool starts automatically when the spindle is pushed
in. This facilitates convenient work. In order to enable
automatic mode, briefl y press the trigger switch.
NOTE
The tool switches to sleep mode after 15 minutes without
use. To activate again: press the trigger switch briefl y.
WARNING
Risk of injury from inadvertent automatic machine start-
up. In automatic mode, do not touch any rotating parts
such as spindle, bit or magnetic bit holder.
Impulse mode
Protruding screws can be precisely countersunk using
this function. Press trigger switch and countersink the
screw with the attached stopper. To switch off release
the trigger switch.
NOTE
○ If the amount of protrusion of the screw is small, the
screw may not tighten.
○ In that case, remove the stopper and make adjustments
Page
in Manual mode.
2
*3 How to use the LED light
NOTE
2
The light goes out automatically 10 seconds after the
2
switch is released.
*4 Setting the direction of rotation, engaging the
3
transporting safety device (switch-on lock)
CAUTION
3
Only activate the rotation selector switch when the motor
3
has completely stopped.
3
4
10
6
11
4
12
4
―
193
Publicidad
