Disposal Of The Product - Maxell YOSO TRIM Manual Del Usuario

How to shave facial hair
■Forehead, cheeks, and jaw
Apply the blade to skin gently, and shave hair slowly in the direction against the flow
of hair. (Fig.6)
■Hairline and around nose
Shave hair in the way properly and refer to picture on the right. (Fig.7)
■Neckline
Hold hair with hand and shave hair just liked the way as razor. (Fig.8)
■Arms and legs
Slowly shave arms from the wrist towards the elbow and legs from the ankle towards the
knee in the direction against the flow of hair. (Fig.9)
How to shave eyebrow
Shave the eyebrow in the way properly and refer to picture on the right. (Fig.10)
Above the eyebrow Eyebrow
How to use the eyebrow comb
Align the eyebrow comb with eyebrow and trimming. The length of eyebrows is capable of
being trimmed are approx. 2mm [short] and approx. 4mm [long] respectively.
Short (approx. 2mm) Long (approx. 4mm)
1. Turn the switch to 0(OFF), attach the blade to eyebrow comb until it clicks. (Fig.12)
・ When trimming eyebrows into 4mm, insert the blade to [long] side of the eyebrow comb.
・ When trimming eyebrows into 2mm, insert the blade to [short] side of the eyebrow comb.
2. Turn the switch to ON, and align the length of eyebrows. (Fig.13)
・ Align the eyebrow comb with eyebrow and close to skin, move slowly from the end to
the beginning of eyebrow. (Fig.14)
How to exchange and clean blade
Make sure to turn the switch to 0(OFF) when cleaning blade.
Use shaver cleaner only.
Do not wash or splash water on the product.
Clean off dirt of product with cloth wrung out with water. Do not use
alcohol, benzine and thinner. It would cause deformation and tarnishing.
Make sure to clean blade after use. Also make sure to use shaver cleaner which is sold
separately because sticky dirt and oil may remain and cause break with cleaning brush only.
How to remove blade
1. Move the removable grip towards the direction of the arrow. (Fig.15)
2. Remove the blade towards the direction of the arrow. (Fig.16)
How to clean blade
1. Clean blade and hair ball on the product with cleaning brush. (Fig.17)
2. After cleaning, spray a bit of shaver cleaner to inside of blade and operate the product
for a while. Then, clean off the blade and surface of the product.
Inside of blade Shaver cleaner
All manuals and user guides at all-guides.com
-3-
How to attach blade
1. If the removable grip is on the lock position, move it towards the direction of the arrow.
(Fig.19)
2. Insert the hole in the front edge of blade into the projection in the edge of the product.
(Fig.20) Hole Projection
3. With pressing rear blade gently against the product, move the removable grip towards
the direction of the arrow. Then, attach the blade to the product. (Fig.21)
4. Put the cap on the blade. (Fig.22)
This mark means that this appliance shall not be used near water contained
in bath-tubs, basins or other vessels.
Trouble shooting
Before requesting repair, check the following:
Symptom
Check Point
The product
Check if battery places
doesn't operate.
in correct direction.
The blade is contaminated
or rusty.
Check if battery power
is consumed.
The product does
Check if any battery other
not give a beautiful
than an alkaline battery is
finish.
being used.
Check whether the blade
is contaminated.
Check the above, and if the face shaver is still not working properly, do not repair by
yourself but consult your retailer.
Specifications
Power supply 1.5V DC; one alkaline battery (LR03/AAA)
Mass Approximately 34g (including batteries)

Disposal of the product

For disposal of the parts, observe your local laws and regulations etc.
Solution
Check the terminal and insert
battery again.
Remove contamination or rust with
a commercially available lubricant
(shaver cleaner).
Exchange old battery to new
alkaline battery.
Use an alkaline battery.
Clean and treat the blade.
-4-