Publicidad
Idiomas disponibles
Idiomas disponibles
The right-hand pedal (41R), marked with the letter (R),
screws onto the right-hand crank (Q), also marked
with an (R), in a clockwise direction. Tighten securely,
Fig.4.
The left-hand pedal (41L), marked with the letter (L),
screws onto the left-hand crank, also marked with an
(L), in an anti-clockwise direction. Tighten securely
Fig. 4.
4 ATTACHING THE SEAT.-
Place saddle back support tube to the upright position
Fig.5. Get screw (75) and place it in the metallic
support piece and tighten securely.
Afterwards, unscrew the screws (65) on the seat (77)
of the saddle back, place it as shown in Fig,5 and
tighten back again the screws securely.
Afterwards, unscrew the screws (64) on the back side
of the saddle back, place it as shown in Fig.6 and
tighten back again the screws securely.
5 FITTING THE HANDLEBAR.-
Take the handlebar tube (96) and position it at the
back of the backrest support, Fig.7. Next, fit the
screws (64) along with their washers (62) and tighten
securely.
Next, take the rear backrest cover (89) and fit the
screws (66) at the back of the backrest (87), Fig.8.
Now take the handgrip signal connector (68), Fig.9,
and plug it into terminal (N), located at the top of the
trim cover (92).
6. FITTING THE HANDLEBAR STEM.-
Connect the two terminals (14; 15) Fig.10, coming out
of the handlebar stem (6) and (18; 19) the main body
(17).
Insert the handlebar stem (6) onto the boss on the
main body (17) taking care not to pinch the cables.
Fit the bolts (12) and fl at washers, as shown in
Fig.10, align the handlebar stem and hand tighten.
7. FITTING THE BOTTLE HOLDER.-
Take the bottle holder (11), insert it in through the top
of the handlebar (6), Fig.11.
Next, release the screws (16) on the handlebar (6),
position the bottle holder and secure it by using the
screws (16) removed previously.
8. FITTING THE MONITOR.-
Bring the monitor (1) to the handlebar stem (6) Fig.12,
connect the two terminals (14; 15) coming out of the
handlebar stem (6) and (A-7; A-8) the monitor (1),
Fig.12.
Insert the monitor (1) onto the handlebar stem (6), as
shown in Fig.12, making sure not to pinch any of the
cables.
Fit the bolts (7) along with the flat washers, making sure
that the handlebar is aligned correctly, securely tighten
all of the bolts on the handlebar stem including the bolts
at the base which were left hand tight in point 6.
9.- FITTING SADDLE ADJUSTMENT KNOB
Place saddle adjustment knob (82) Fig.13, turning it in
a clockwise direction into the handle (U).
ADJUSTING THE SEAT.-
The seat can be adjusted by pressing lever (U) Fig.14,
upward, this is on the lower right-hand side of the
seat, and, without releasing it, sliding the seat
backwards or forwards to suit your seating position.
Once the seat is in a position that suits you, lower the
lever (U) and the seat will be locked into this position.
LEVELLING.-
Once the unit has been placed into its fi nal po- sition,
make sure that it sits fl at on the fl oor and that it is
level. This is achieved by screwing the adjustable foot
(60) up or down, Fig.15.
MOVEMENT & STORAGE.-
The unit is equipped with wheels (49) to make it
easier to move about. The two wheels at the front of
the unit make it easier to place the unit in any chosen
position, as shown in the Fig.16. Store it in a dry
place,
preferably
temperature.
MAINS CONNECTION.-
Insert the jack (M) on the transformer (103) into the
connection hole (K) on the main body (17) (bottom,
rear of the machine) and then plug the transformer
into a 220 V mains supply, Fig.17.
BH RESERVES THE RIGHT TO MODIFY THE
SPECIFICATIONS OF ITS PRODUCTS WITHOUT
PRIOR NOTICE
9
MOD. H-750
not
subject
to
changes
in
Publicidad
