Publicidad
ENGLISH
VBV-770B VEHICLE CCTV SYSTEM
INTRODUCTION
This vehicle CCTV system has been designed to provide years of trouble-free
operation. Please read this manual thoroughly. This manual contains instruc-
tions to make the installation of the camera and monitor easier. The vehicle
CCTV system is a supplement to standard rear-view mirror systems, and will
provide additional rear-view vision when installed and maintained properly.
It is not intended in any way to be a substitute for careful and cautious driving.
All applicable traffic laws and motor safety regulations must still be adhered to.
FEATURES
VBV-700C CAMERA
•
300,000 pixel image sensor
•
0.1 Lux sensitivity (18 IR-LED)
•
Auto White Balance (AWB)
•
Field of view 110° Diagonal
•
Back Light Compensation (BLC)
•
Automatic electronic iris provides a clearer, more consistent image in low
and bright light
•
Compact and lightweight design installed easily into most vehicles
•
Waterproof cable connection (IP67)
•
Wind deflector reduces build up of dirt on lens
•
CE/e-marking
VBV-770BM TFT LCD COLOUR 7.0" (178mm) MONITOR
•
Menu button for Picture, System and Options
•
Camera 1/Camera 2 /Camera 3
•
Power/stand-by switch
•
CE/e-marking
CONTENTS OF 1 COMPLETE SYSTEM
VBV-700C CCD CAMERA
1 Camera
1 Camera bracket
4 Attachment screws with washers
1 Wind deflector
1 VBV-770BM MONITOR
1 Monitor
1 Sunshield
1 Monitor bracket
1 Remote control
1 Monitor mounting bracket
BEFORE INSTALLATION
1. This system operates from 10 volts DC to 32 volts DC, negative ground.
2. Please install this system according to the instructions in this manual.
3. Do not disassemble the camera or the monitor. This voids the
warranty. Disassembling the camera will compromise the Waterproof seal.
4. Connect the system to an ignition switched power source. Connection to a
battery source will reduce battery life.
WARNING
1. To prevent electrical shock, DO NOT OPEN THE MONITOR CASE.
There are potentially lethal voltages inside the monitor. There are no user
serviceable parts inside. If evidence of tampering is detected, the warranty
will be considered void.
2. Keep monitor away from leaking water, rain, moisture etc. It is NOT water-
proof. Any moisture inside the monitor could cause extensive damage.
3. Use the self-tapping screws to mount the monitor to the dashboard or
headliner.
INSTALLATION INSTRUCTIONS
VBV-700C CAMERA
1. Attach camera bracket (see Fig. 1) to upper portion of vehicle.
Attachment point must be sturdy enough to support camera and bracket.
2. Attach camera to bracket using screws provided. Adjust angle as indicated
in Fig. 2. (Use rear bumper and back of vehicle as a reference point.)
3. Wind deflector may be installed. This deflector is designed to reduce the
build up of dust, dirt and moisture on the camera lens. (See Fig.3)
VBV-770BM MONITOR
1. Attach monitor inside vehicle in a location convenient to the driver (e.g.
centre of dash, overhead or in dash).
2. Use a compression plate or rear-mounting bracket to attach the monitor
bracket to the dash or overhead.
3. Adjust mounting angle of the monitor to allow driver to easily view the
screen from all seat positions. (See Fig. 4.)
CABLE
1. The camera to cable connection is waterproof. The cable to control box
connection is not waterproof. Be sure to position the cable properly. The
male end attaches to the camera. The female end attaches to the control
box. (See Fig. 5.)
2. Do not run the cable over sharp edges or corners. Do not kink the cable.
Keep the cable away from hot and rotating parts.
3. Place all excess cable in convoluted tubing.
4. Wire the cable securely.
WIRING CAMERA AND MONITOR
1. See wiring diagram for connections to ignition, ground and back up circuit.
(See Fig. 5.)
2. Wiring camera: Drill a 20mm (0.8in) diameter hole into vehicle body near
the camera and bracket. Connect camera connector to extension cable in
vehicle. Push extra cable into vehicle (be careful not to kink cable) and fit
grommet into hole. Apply sealant around grommet to increase resistance
to water penetration.
3. Wiring the monitor: insert extension cable into camera CA3 reversing
camera position; if CA1 or CA2 camera is used, be sure to mark each
extension cable properly and plug second and third cable into camera
CA1 or CA2 position. Bundle excess cable together using a cable tie or
vinyl tape. This will avoid possible damage to cable during operation.
4. The red wire is connected to an ignition power source, the black wire is
connected to chassis ground, the brown wire is connected to the vehicle's
back light circuit.
5. ONLY PETROLEUM ROAD TANKERS: All electrical equipment fitted to
petroleum vehicles must be fitted via battery master switch and must be
isolated from the battery while the vehicle are loading and unloading.
6. Always consult your dealer when fitting any electrical or electronic
equipment to a vehicle fitted with a CAN-bus system.
All manuals and user guides at all-guides.com
FUNCTIONS AND OPERATION
MONITOR
1. POWER LED
When the red LED is on, it indicates power on.
When a trigger is selected, the image shown by cameras will be shown
on the monitor.
2. Stand by ON/OFF Switch
3. L /M CONTROL BUTTON
These control buttons are used to scroll up and down to select menu
options
4. SEL.
SELECT CONTROL BUTTON
Use these buttons in order to select the required option in the menus.
5. 'MENU' Button
If you press the 'MENU' button, the following list of functions will be
shown on the monitor.
• PICTURE
• OPTION
• SYSTEM
The menu list will disappear if no selection is chosen within 5 seconds.
6. CA.SEL
Camera selector button
Enables selection of CA1, CA2 and CA3.
The OSD indicates which camera is currently operating.
7. REMOTE-CONTROL SENSOR
The monitor can be operated via remote control. If using remote control,
ensure that the IR on the remote control is facing the monitor.
HOW TO SET YOUR MONITOR TO YOUR REQUIREMENTS
1. PICTURE CONTROL
1.1 Press the MENU button
1.2 Select PICTURE
1.3 Move the cursor to the VOLUME, BRIGHT, CONTRAST, COLOUR and
1.4 Press the L /M button
SHARP with the SEL button
1.5 Select one of five options
1.6 Press the MENU button
2. OPTION CONTROL
2.1 Press the MENU button
2.2 Select SEL
2.4 Press the L /M button
2.3 Move the cursor to the LANGUAGE with the SEL button
2.5 Select one of seven language options
2.6 Press the MENU button
2.7 Move the cursor to the SCALE with the SEL button
2.8 Press the L /M button
2.9 Select one of two options
2.10Press the MENU button
2.11Move the cursor to one of three CA option with SEL button
2.12Press the L /M button
2.13Select one of two options to view NORMAL or MIRROR image. NOTE:
changing the image will also change the OSD
3. SYSTEM CONTROL
3.1 Press the MENU button
3.2 Select SYSTEM
3.3 Move the cursor to the COLOUR SYSTEM, BLUE BACK, HORIZONTAL,
VERTICAL with the SEL button
3.4 Press the L /M button
3.5 Select one of five options
3.6 Press the MENU button
REMOTE CONTROL (See Fig.A)
1. POWER (Power switch). Press this button to turn the monitor on and off
of stand by
2. L SEL - Press this button to move up the menu
3.
- This button flips the picture vertically
4. + - This button increases the selection
5. SEL M - Press this button to move down the menu
6. CALL - This button displays which camera is being viewed
7. TIMER - The timer can be set to automatically switch off the monitor (120
minutes maximum)
8. CA.SEL (CA1/CA2/CA3 shift) - Press this button to switch between CA1,
CA2 and CA3
9. SYS - This button displays the SYSTEM CONTROL menu
10. LANG - Press this button to select a language (English, French,
Portuguese, Spanish, Russian, Turkish, German, Italian and Bulgarian)
11. MODE - Selects different picture modes (Standard, Soft, Vivid, Light and
Personal)
12. MENU - Press to display the Main Menu
13.
- This button decrease the selection
14.
-This button flips the picture horizontally
15. MUTE - Press to select ENABLE/MUTE sound
CAMERA
Waterproof connector (See Fig.6)
CAUTION
1. DO NOT OPEN THE CAMERA CASE. This will break the camera's
waterproof seal. If evidence of tampering is detected, the warranty will be
considered void.
2. We do not recommend mounting the camera near the lower area of the
vehicle (e.g. bumper). This reduces the view of the camera and increases
the chance of physical damage to the camera.
3. Use only the inner hexagonal screw and washers to mount the camera.
MAINTENANCE
Remove dust and dirt with a damp soft cloth. Heavier dirt should be removed
with a damp soft cloth and mild detergent. Do not use strong cleaning agents
containing gasoline, thinner, benzene or alcohol.
These substances may damage the exterior surface of the monitor.
CAUTION
1. Before drilling, be sure no cable or wire is on the other side. Be sure to drill
a 20mm (0.8in) diameter hole only.
2. Feed as much cable as possible into vehicle and clamp securely. This
reduces the possibility of it being hooked or snagged.
3. Keep all cables away from HOT, ROTATING and ELECTRICALLY NOISY
components.
4. To increase protection of cable, place all excess wire and extension cable
in convoluted tubing.
5. Do not twist camera cable and do not cut camera pigtail or cable.
SPECIFICATIONS
VBV-700C CAMERA
PICK-UP DEVICE
INTERLINE TRANSFER TYPE CCD
TV SYSTEM
PAL
PICTURE ELEMENTS
512(H) x 582(V) PAL
SENSING AREA
0.2x0.1in (4.9mm x 3.7mm)
IMAGE SIZE
1/3 inch
SYNCHRONIZATION
INTERNAL
HORIZONTAL RESOLUTION
380 TV LINES
REQUIRED ILLUMINATION
0.1 LUX MINIMUM/F1.2
SIGNAL TO NOISE RATIO
MINIMUM 48dB(AT AGC OFF)
POWER SUPPLY
12Vdc
POWER CONSUMPTION
3.5W(AT 12Vdc)
CURRENT CONSUMPTION
MAX. 300mA
LENS ANGLE
110º(D), 88º(H),66º(V)
OPERATION TEMPERATURE
-20ºC TO +70ºC
STORAGE TEMPERATURE
-30ºC TO +60ºC
WEIGHT
0.2Kg (0.41lb)
DIMENSIONS (W x H x D)
2.7x1.7x2.1in (70 x 44 x 54mm)
VBV-770BM MONITOR
PICTURE TUBE
7.0 inch (178mm), COLOUR TFT-LCD
DEFLECTION ANGLE
60°(LEFT/RIGHT), 40°(TOP), 60°(DOWN)
POWER CONSUMPTION
10W MAXIMUM
POWER SOURCE
10-32Vdc
TV SYSTEM
PAL/NTSC
VIDEO INPUT/OUTPUT
COMPOSITE VIDEO SINGLE
1VP-P 75 OHM
RESOLUTION
1440(H) x 234(V)
CONTRAST
250:1
BRIGHTNESS
450cd/m
2
VIEWING ANGLE (U x D x R/L)
30 x 60 x 60
OPERATING TEMPERATURE
-20°C TO +70°C
STORAGE TEMPERATURE
-30°C TO +80°C
WEIGHT
0.63Kg (1.37lb)
OUTER DIMENSIONS
7.1x4.8x1.0in (182 x 122 x 26mm)
(W x H x T)
(without flush mount)
DISCLAIMER
The use of the VBV-770B Vehicle CCTV system should not in any way be used
as a substitute for careful and cautious driving. Traffic laws and motor safety
regulations must always be adhered to.
Specification subject to change without any notice.
Publicidad
