Publicidad
Idiomas disponibles
Idiomas disponibles
GB
OPERATION
CAUTION! Before assembly and dismantling, firstly switch product off and disconnect the plug from the outlet.
Assembly and dismantling
Place the product on even and stable surface. Make sure that all suction cups adhere to the surface. The surface shall be smooth
and clean. If suction cups fail to adhere to the surface, check if suction cups are clean and then slightly moisten them.
To place the pot on the base, insert the pot so that handle was towards open padlock symbol, and then turn it to closed padlock
symbol (II). Proper position of pot prevents lifting thereof and couples the pot to the base. To release the pot, turn and set the
handle towards the open padlock symbol, and then lift the pot over the base.
Pot cover is provided with the gasket that shall be placed on the cover flange perimeter so that it adheres evenly to the whole
flange, and narrow flange of gasket is positioned towards cover lower part (III). Place the cover on the pot, so that it adheres
evenly to pot edge (IV), and so that latch was activated that prevents against cover accidental opening. Product is provided with
sensor indicating an improper position of cover or improper position of pot. Flashing „E01" symbol on display indicates improper
cover position that prevents product operation. Product operation will be possible, if cover is positioned properly. To remove the
cover, press and hold the button that releases the latch (V), and then take off the cover.
Caution! Proper position of pot locks the cover and prevents cover removal. You can remove the cover only, if the pot is un-
locked.
The cover is provided with the hole that enables to add some food products, e.g. during product operation. To close the hole, place
the cap on the cover and then turn it so that tongues of pin couple with tongues inside the hole (VI). You can also use the pin to
measure quantity of used food products.
You can install the butterfly stirrer inside the pot, by placing it on pot blade screw so that stirrer wings are positioned between the
blades (VII).
Product may be used for steaming thanks to the sieve and bowl delivered for that purpose. To install the sieve insert in into the
pot, so that sieve flange rests against pot walls (VIII). You can remove the sieve by pulling with the folding holder. The holder may
be very hot so always take caution and wear an oven glove.
CAUTION! You can operate the product with installed sieve or butterfly stirrer.
To install the bowl on the pot cover, remove the cap, and then place bowl bottom on the cover. You can install the bowl in proper
position only. The base it provided with tongues. The narrow tongue indicates position of pot holder (IX).
The bowl is provided with insert and cover. The insert shall be placed inside the cover to increase the working surface when steam-
ing. Insert sides are provided with holes that couple bowl tongues (X). The cover shall be placed on the bowl (XI).
Simultaneous use of sieve and bowl for steaming is not recommended, as it compromises processing efficiency. For steaming
purposes, the pot may be filled with max. 0.5L of water.
Control Panel
After assembly completion in proper configuration, product operation may follow with control panel provided with buttons, knob
and display. Upon activation the display test will follow and all readings will be shown for a few seconds, and it does not indicate
any malfunction.
"OVERLOADING" indicator will light to indicate excessive weight. This abnormality is indicated also with "E04" symbol on display.
In this case weight of food products shall be reduced.
"OVERHEATING" indicator will light to indicate product overheating, namely pot temperature over 150
O
C. This abnormality is
indicated also with "E03" symbol on display. In this case, wait until temperature of the product will be within permitted range.
Press "AUTO" button to select the mode: soup, jam, sauce, dough, steaming.
Press "MANUAL" button to manually program the following settings: temperature, time, speed.
Press "SCALE" button to weigh food products.
Press "START/PAUSE" button– inside the control knob to switch the product on and off. Press the button again to restore opera-
tion.
Press "STOP" button to interrupt product operation.
Press "TURBO" button to activate maximum rotational speed of blades for some time. For this purpose press and hold this button.
Release of button will switch off maximum rotational speed.
The control knob enables to program settings. To increase the setting, turn the control knob clockwise and to reduce the setting
turn the control knob anti-clockwise.
Control panel
When "AUTO" button is presses, soup mode will start flashing, and press the button again to select available mode: soup, jam,
sauce, dough, steaming.
To activate the mode press "START/PAUSE" button, and then the product operation will follow in the selected mode.
To interrupt operation in current mode, press "START/PAUSE" button. Then the clock stops, and symbol of selected mode will start
flashing on display. To restore operations, press "START/PAUSE" button again.
To stop product operation press "STOP" button.
O R I G I N A L
I N S T R U C T I O N S
14
Publicidad
