Prior Using For The First Time; Set The Water Softener - Kunft KDW4752N Manual De Instrucciones

Syphon connection
The waste connection must be at a height of between 50 cm
(minimum) and 100 cm (maximum) from the bottom of the dish. The
water drain hose should be fixed by a hose clip.
Before starting the dishwasher
The followings should be observed before starting the dishwasher:
1. Whether the dishwasher is levelled and fixed;
2. Whether the inlet valve is opened;
3. Whether there is a leakage at the connections of the conducts;
4. Whether the wires are tightly connected;
5. Whether the power is switched on;
6. Whether the inlet and drain hoses are knotted;
7. All packing materials and printings should be taken out from the
dishwasher.
Attention
After installation, please put this manual into the bags of printings, as
its content is very helpful to the users.

Prior Using for the First Time

Before using your dishwasher for the first time, refer to the
following items:
A. Set the water softener
B. Fill the salt container
C. Fill the rinse aid dispenser
D. Detergent
A. Set the water softener
The water softener is designed to remove minerals and salts from
the water, which would have a detrimental or adverse effect on the
dishwasher's operation. The higher the content of these minerals
and salts, the harder the water is. The softener should be adjusted
according to your area's water hardness. Your local Water Authority
can advise you on the water hardness in your area.
Setting
The amount of salt dispensed can be set from H0 to H7.
Salt is not required at the set value H0.
1. Find out about the water hardness in your area. Your water utility
company will help you with this.
2. Set value can be found in the water hardness table.
3. Close the door.
4. Switch on "Power" switch.
16
dishwasher
5. Hold down " Delay" button and then press "Programme" button for
5 seconds.
The buzzer rings one time and "H..." flashes on the digital display
(factory setting is H4).
To change the setting:
1. Press the "Delay" button.
Each time the button is pressed, the set value increases by one
level; when the value of H7 has been reached, the display jumps
back to H0 (off).
2. Press the "Programme" button. The chosen setting has now been
stored.
Contact your local water board for information on the hardness of
your water supply.
Water hardness table
Water hardness
°Clark Range
0 - 8 soft
9 - 10 soft
11 - 12 medium
13 - 15 medium
16 - 20 medium
21 - 26 hard
27 - 38 hard
39 - 62 hard
WATER SOFTENER
The hardness of the water varies from place to place. If hard water is
used in the dishwasher, deposits will form on the dishes and utensils.
The appliance is equipped with a special softener that uses salts
specifically designed to eliminate lime and minerals from the water.
B. Fill the salt container
The salt container is located beneath the lower basket and should
be filled as follows:
Attention!
Only use salt specifically designed for use in dishwashers! All other
types of salt not specifically designed for use in a dishwasher,
especially table salt, will damage the water softener. In case of
damages caused by the use of unsuitable salt the manufacturer does
not give any warranty nor is liable for any caused damages.
EN
KDW4752N
Set value on
Mmol/l
the machine
0 - 1.1 H0
1.2 - 1.4 H1
1.5 - 1.8 H2
1.9 - 2.1 H3
2.2 - 2.9 H4
3.0 - 3.7 H5
3.8 - 5.4 H6
5.5 - 8.9 H7
17