Publicidad
Idiomas disponibles
Idiomas disponibles
h.-
/
/ CH+: in playback mode, a short press of this button starts and pauses playback. A long
press allows playback selection among (RAN) random playback, (SIN) repeat a track, (FOL) repeat
1
folders, (ALL) repeat all. In radio mode, this button allows successive changes among the stations
stored during the automatic tuning.
i.-
: button to switch off the USB/SD/MP3 player with FM tuner.
9.- FM/MP3: these microswitches allow the USB/SD/MP3 player with digital FM tuner module signal to be
Z
PRIORITY
ON / OFF
MIC
1
2
INPUTS
allocated to one or several output zones. Place the corresponding microswitch (1 a 4) in the ON position
and the source will be heard in that or those zones.
2
3
10.- These microswitches allow the input signal INPUT 5 to be allocated to one or several output zones.
Place the corresponding microswitch (1 a 4) in the ON position and the source will be heard in that or
those zones.
11.- INPUT 5: auxiliary input, 3'5 mm jack connector.
12.- Z1-Z2-Z3-Z4: selectors to allocate one or several output zones to the headphones output. Press the
buttons to send the desired zone or zones to the headphones output.
13.- Headphones output, 6.3 mm stereo jack connector.
14.- Headphones output volume control.
REAR PANEL
~115 V AC, 50/60 Hz FUSE: T1.6 A 250 V
~230 V AC, 50/60 Hz FUSE: T0.8 A 250 V
FUSE
1
2
1.- AC power supply socket.
2.- Mixer/Preamplifier on/off switch.
3.- ZONE 1-ZONE 4 REMOTE VOL: outputs for remote control of output zones volume. Connect a
potentiometer in the desired zones to control the volume remotely. For more information, consult the
section Instructions for Use.
4.- ZONE 1-ZONE 4 BAL. OUTPUT: balanced line level outputs for zones Z1 to Z4, XLR connectors.
5.- FM ANT: FM antenna input.
6.- INPUT 4: auxiliary input, 2 x RCA connectors.
7.- INPUT 2-INPUT 3: microphone/line balanced inputs, combo connector (XLR and 6.3 mm jack).
8.- PHANTOM +48V: phantom power supply selector +48 V. Activate this selector when connecting an
electret condenser microphone to the input which requires phantom power supply (48 V between pins
2 and 3 of the XLR connector).
9.- GAIN: INPUT 2 and INPUT 3 sensitivity level. Allows the input sensitivity to be adjusted according to the
required level. If a microphone is being connected, set the control at its minimum level. If connecting
to a line level input, set the control approximately halfway. Adjust the control until an ideal sensitivity is
achieved.
10.- INPUT 1: dynamic microphone balanced input, combo connector (XLR and 6.3 mm jack).
4
MULTIZONE MIXER / PREAMPLIFIER MX-867RU
Z
Z
SIG
3
4
Z1
Z2
5
ZONE 4
ZONE 3
BAL. OUTPUT
BAL. OUTPUT
REMOTE
REMOTE
REMOTE
VOL
VOL
3
7
FM RADIO & MP3 PLAYER
SIG
SIG
SIG
Z3
Z4
ZONES
6
4
ZONE 2
ZONE 1
FM ANT
BAL. OUTPUT
BAL. OUTPUT
REMOTE
VOL
VOL
- 3 -
9
Z
VOL-
VOL+
FM / MP3
EQ
AUX
MODE
SCAN
CH+
Z
INPUT 5
INPUTS
8
10
11
a
FM RADIO & MP3 PLAYER
MODE
b
c
7
INPUT 4
INPUT 3
INPUT 2
GAIN
PHANTOM
+48 V
8
5
6
EN
12
Z1
Z2
Z3
Z4
MONITOR
13
14
d
e
VOL -
VOL +
EQ
SCAN
CH +
f
g
h
i
INPUT 1
GAIN
PHANTOM
+48 V
9
10
Publicidad
