Publicidad
Idiomas disponibles
Idiomas disponibles
Close delay will go back to standard setting.
*LED ENCODER:
ENCODER OPERATION signaling LED. During the gate stroke, the LED flashes red.
E1 - Red
The flashing varies according to the motor speed.
OPTIONAL LIMIT SWITCH LEDS:
The LEDs are steady on as long as the gate is moving, while one of the two LEDs switches off when:
LFCA - off
the LED signals the arrival at the opening limit switch
LFCC - off
the LED signals the arrival at the closing limit switch
9. RESTORING AUTOMATIC OPERATION
Should the Bar need to be operated manually, use the release system. After the manual operation:
•
after a Mains Power Failure, such as a black-out (controller remains disconnected for a certain time)
or after a manual release (without power shortage to the controller for more than 5 seconds), the
automation will be moving slowly to allow the Controller to establish its Limits (REALIGNMENT
procedure).
10. 433.92 MHz BUILT-IN RADIO RECEIVER
The radio receiver can learn up to a maximum of 30 codes of rolling code (S2RP, S4RP, K-SLIM-RP,
T-4RP) to be set freely on 3 channels.
The first channel directly commands the control board for opening the automatic device; the second
channel commands a relay for a N.O. no-voltage output contact (terminals 19 - 20, max. 24V AC, 1 A)
and the third channel controls directly the pedestrian opening from the controller.
LEARNING SYSTEM FOR RADIO CONTROL DEVICES
CH1 = 1
channel (OPEN/CLOSE)
st
1_ Press button CH1 briefly to associate a radio control device with the OPEN/CLOSE function;
2_ the (green) DL2 LED is ON to indicate the code learning mode has been activated (if no code is
entered within 10 seconds the board exits the programming function);
3_ press the button of the relative radio control device;
4_ the (green) DL2 LED turns off to indicate saving is complete and then on again immediately waiting
for other radio control devices (if this is not the case, try to re-transmit or wait 10 seconds and
restart from point 1);
5_ to memorise codes to other radio control devices, press the key to be stored on other devices
within 2-3 sec. After this time (DL2 LED turns off) must repeat the procedure from point 1 (up to a
maximum of 30 transmitters);
6_ if you wish to save on the 2nd channel, repeat the procedure from point 1 using the CH2 key instead
of CH1 (in this case the DL2 LED is yellow);
7_ to program transmitters into the third channel, repeat procedure from point 1 using CH1 and CH2
buttons at the same time (DL2 will turn on red);
8_ to exit the learning mode without memorising a code, press button CH1 or CH2 briefly.
If the maximum number of radio controls is reached (30), the LED
rapidly for about 3 seconds but without performing memorisation.
REMOTE PROGRAMMING BY MEANS OF T-4RP / K-SLIM-RP / S-2RP / S-4RP (V 4.X)
With the new version of software V 4.X it is possible to carry out the remote self-learning of the new
version of transmitters T-4RP / K-SLIM-RP / S-2RP / S-4RP (V 4.X), that is without pressing the receiver's
programming buttons.
It will be sufficient to have an already programmed transmitter in the receiver in order to start the
procedure of remote programming of the new transmitters. Follow the procedure written on the
instructions of the transmitter T-4RP / K-SLIM-RP / S-2RP / S-4RP (V 4.X).
CH2 = 2
channel
nd
24
CH1+ CH2= 3
channel CH3 (PEDESTRIAN)
rd
DL2
will begin to flash
Publicidad
