Publicidad
Idiomas disponibles
Idiomas disponibles
ADDITIONAL SAFETY RULES FOR BATTERIES AND
CHARGERS
ES
Use batteries and chargers applicable to this machine.
BATTERIES
PT
• Never try to open for any reason.
• Do not store in places where the temperature may exceed 40 C.
• Charge only at room temperature between 4ºC and 40ºC.
EN
• When disposing of batteries, follow the instructions given in the
section "Protecting the environment".
• Do not short circuit. If the connection is made between the
FR
positive (+) and negative (-) terminal directly or by accidental
contact with metal objects, the battery will be short-circuited
and a strong current will flow causing heat generation which may
cause the case to break. or a fire.
• Do not heat. If batteries are heated above 100 C, the sealing
and insulation separators and other polymeric components can
be damaged, causing electrolyte leakage and/or internal short
circuits leading to heat generation and rupture or filing. Also, do
not dispose of batteries in fire, as explosions and/or severe burns
may result.
• Under extreme conditions, battery leakage may occur. When you
notice liquid in the battery, proceed as follows:
• Carefully wipe off the liquid with a cloth. Avoid contact with skin.
• In case of contact with skin or eyes, follow the instructions below:
1. Rinse immediately with water. neutralize with an acid
mild as lemon juice or vinegar.
2. In case of contact with eyes, rinse thoroughly with
clean water for at least 10 minutes.
3. Consult a doctor.
Fire danger! Avoid shorting the contacts of a battery. Do not
incinerate the battery.
CHARGERS
• Never try to charge non-rechargeable batteries.
• Replace defective cables immediately.
• Do not expose to water.
• Do not open the charger.
• Don't test the charger.
• The charger is designed for indoor use only.
OPERATION
Before using the equipment:
Instruction manual
BATTERY CHARGER
The lithium ion battery can be charged at any time and will not develop
a "memory" when charged after partial discharge. It is not necessary
to deplete the battery charge before recharging it. Remove the battery
pack from the tool when it is convenient for you and your work. You can
"top off" your battery pack before starting a big job or a long period
of use. Due to the non-fading properties of lithium-ion, the only time
the lithium-ion battery pack needs to be charged is when the pack has
reached the end of its charge. To signal the end of charging, the power
to the tool will rapidly reduce. Charge the battery as needed.
CHARGING THE BATTERY
This lithium-ion battery pack ships partially charged. Before using it for
the first time, fully charge the battery. A fully discharged 2.0Ah battery
with a temperature between 4 C and 40 C will charge in approximately
1 hour.
Plug the charger adapter into the power source. The green light on the
charger cradle will illuminate, indicating that the charger is on.
Slide the battery all the way into the charger mount. The red light on
the charger cradle will illuminate, indicating the battery is charging.
The red light will turn off after charging is complete and a green light
will appear.
normal. If the battery is hot after continuous use on the tool, allow
it to cool to room temperature before charging. This will extend the
life of your batteries.
before making any assembly or changing accessories.
RECHARGEABLE BATTERY INSERTION AND REMOVAL
adjustments to the equipment. Be sure to read the following
information before operating your wireless equipment: Charge the
battery with the charger. An empty battery requires a charging
period of approximately 0.5 to 1 hour.
FUNCTIONS
adjustments to the equipment.
Be sure to read the following information before operating your wireless
NOTE: Batteries can become hot during charging. This is
WARNING: Always disconnect the battery pack from the tool
• Press the battery release button located on the front of the
battery pack to release the battery pack.
remove it from the tool.
WARNING: Always remove the battery before making any
• Insertion and removal of rechargeable battery.
• Press the battery release button located on the front of the
battery pack to release the battery pack.
• Pull out the battery and remove it from the tool.
WARNING: Always remove the battery before making any
08787
REF.
Pull out the battery and
Publicidad
