Descargar Imprimir esta página

Premium PFB2000 Instrucciones De Uso página 2

Publicidad

Idiomas disponibles

Idiomas disponibles

Important Safety Instructions
1.In order to reduce fire and electric shock hazards and injuries while using this
electric equipment, always follow these basic precautionary measures.
2.This fan is intended for domestic use, and is not suitable for commercial, industrial
or outdoor use.
3.DO NOT place in or near a window, to avoid contact with the outdoor elements and
to avoid exposure to direct sunlight. Rain may create an electrical hazard.
4.DO NOT immerse fan, plug or cord in water/liquid. DO NOT spray with water/liquid.
5. Always use on a dry leveled surface.
6.Unplug fan when not in use, moving fan to another location or cleaning.
7.Do not let cord hang over the edge of a table or counter, or let it touch any hot
surfaces. Do not operate fan with a damaged cord, plug or after the fan malfunctions
or has been dropped or damaged in any manner.
8.Do not operate in the presence of explosive and/or flammable fumes.
9.Do not place fan or parts near an open flame, cooking or other heating appliance.
10.Do not operate without fan grill properly in place.
11.Avoid contact with moving parts.
12.Close supervision is necessary when any appliance is used by or near children.
13.Do not hang or mount fan on a wall or ceiling.
14.The use of fittings not recommended by manufacturer may be hazardous.
15.This appliance has a polarized plug (one blade is wider than the other) to reduce
the risk of electric shock. This plug is intended to fit in a polarized outlet only one
way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit,
contact a qualified electrician. DO NOT attempt to defeat this safety feature.
16.This electric apparatus is unsuitable for use by the following people unless
guardians responsible for their safety are supervising: Children, people with
disabilities, and those with a lack of experience or relevant knowledge.
17.This product employs overload protection fuse. A blown fuse indicates an overload
or short-circuit situation. If the fuse blows, unplug the product from the outlet.
Replace the fuse as per the user servicing instructions. Follow product marking
for proper fuse rating and check the product. If the replacement fuse blows, a
short-circuit may be present and the product should be discarded or returned to
an authorized service facility for examination and/or repair.
18.Do not operate any fan with a damaged cord or plug. Discard fan or return to an
authorized service facility for examination and/or repair.
19.Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or
similar coverings. Do not route cord under furniture or appliances. Arrange cord
away from traffic area and where it will not be tripped over.
1
READ AND SAVE THESE INSTRUCTIONS
WARNING: To reduce the risk of fire or electrical shock,
DO NOT use this fan with ANY SOLID STATE speed control device.
User servicing instructions
1. Grasp plug and remove from the receptacle or other outlet device.
Do not unplug by pulling on cord.
2. Open fuse cover. Push on tabs located next to the blades.
3. Risk of fire. Replace fuse only with 2.5 Amp, 125 V fuse.
4. Remove fuse carefully.
5. Close fuse cover. Push cover closed so that all tabs latch.
FOOT ASSEMBLING
1. Put the fan upside down and slide foot into the slot on fan base.
2. Tighten the screw with a screw driver.
OPERATION INSTRUCTIONS
1.Set the fan on a dry leveled floor. Do not use your fan on a desk.
Do not mount your fan in a window.
2.Plug the power cord into a standard 120 V AC wall outlet.
3.Turn the speed control knob to the desired position:
High (3), Medium (2) or Low (1)
CARE AND CLEANING
1. Turn OFF the control and unplug the fan before cleaning or servicing.
2. Use only a soft damp cloth to clean the fan.
3. DO NOT immerse the fan in water and never allow water to drip into the
motor housing.
4. Do not use gasoline, paint thinner or other chemicals to clean the fan.
5. Remove the front grill.
6. Wipe the blade and grills.
7. Reassemble the fan by snapping the front grill into place.
8. Store the fan in its original box or cover the fan to protect it from dust.
Store it in a cool dry place.
2

Publicidad

loading