Descargar Imprimir esta página

Connecting To A Compressed Air Supply; Cleaning, Maintenance And Ordering Of Spare Parts - EINHELL TC-PW 610 Compact Manual De Instrucciones Original

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 66
Performance values of the compressor:
The compressor used should have a tank volume
of at least 50 liters.
Setting values for work with the suction
spray gun:
Set a maximum working pressure of 8 bar at your
compressed air supply.
Remember:
Wear the necessary protective clothing, in
particular safety goggles, when working with
the screwdriver.
Pay attention to the safety regulations.
5.1 Lubricating the tool
Each time before starting and during prolonged
operation:
Insert 3-5 drops of special compressed air oil
(not included in delivery) into the compressed
air connection (9)
Let the equipment run briefly so that any sur-
plus oil is blown out.
5.2 Inserting/removing a tool (Fig. 1)
Fit the required drive socket insert by pushing
onto the square drive mount (3).
Remove the drive socket insert by pulling it off the
square drive mount (3).
6. Operation

6.1 Connecting to a compressed air supply

Connect the nipple (5) to the quick-lock coup-
ling of a compressed air hose (the hose is not
supplied).
Note the maximum permissible operating
pressure of the equipment.
6.2 Rotational direction switch/torque switch
(Fig. 4)
You can select clockwise or counter-clockwise ro-
tation by turning the rotational direction switch (2).
Turn the setting wheel (8) in order to set the
torque. Please note that the torque can be set
only in clockwise rotation.
1 – Low torque
2 – Medium torque
3 – High torque
Anl_TC_PW_610_Compact_SPK13.indb 15
Anl_TC_PW_610_Compact_SPK13.indb 15
GB
In counter-clockwise rotation there is one level for
undoing the screws.
Important!
To avoid gear damage, make sure that the tool
has come to a complete stop before you change
the direction of rotation.
6.3 Working with the impact driver
Loosening:
Set the direction of rotational direction switch
(2) to counter-clockwise.
Mount a drive socket insert on the impact dri-
ver (see point 5.2).
Place the impact driver on the screw/nut and
press the trigger lever (1).
If the screws/nuts are very tight or if they are
rusted, use a tire wrench or torque wrench to
slightly loosen them.
Tightening:
Warning! Use the impact driver only for loo-
sening screws/nuts. If you want to use the
impact driver to tighten screws and nuts, you
must also use a torque limiter which is desig-
ned for this purpose. If not, the screw connec-
tion may be damaged. The torque limiter is
available from your dealer. It is not included in
the scope of this delivery.
Prior to tightening, carefully insert the screw/
nut into the threads.
It is important that screws/nuts with special
torque specifications (for example provided
by the vehicle manufacturer in the automoti-
ve sector) are tightened only with a suitable
torque limiter.
Danger!
Screws/nuts must be fi nish-tightened with a
torque wrench which is set to the torque speci-
fi ed by the manufacturer and then they must be
checked!
7. Cleaning, maintenance and
ordering of spare parts
Disconnect the compressed air supply from the
equipment before performing any cleaning work.
7.1 Cleaning
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
- 15 -
18.08.2021 15:04:44
18.08.2021 15:04:44

Publicidad

loading