Publicidad
Idiomas disponibles
Idiomas disponibles
English
DOUBLE ACTION CARABINERS
CAUTION: On some occasions the tools a user
has to carry for specific work at all heights do
not come with built-in or prescribed attachment
options for the tool lanyard connection. The
D
WALT range of tool attachments are the perfect
E
solution for such cases and help provide a secure
connection for the tool lanyard in the tethering
system. Different tools will require different
tethering system components depending on their
shape and weight. Do not use the tethering system
for pulling or towing objects.
Turn Clockwise
Push
Spring Action Lock
to Unlock
DOUBLE ACTION CARABINER WITH SWIVEL
WARNING:
When using Retrofit Tool or
Anchor Attachments, the user must ensure that
the Maximum lanyard length identified on the
attachments is compatible with the identified
lanyard length indicated on the tool lanyard
label. Failure in doing so may not give optimum
utilization of the connection made.
8
WARNING:
When using power tool lanyard and
accessories, basic precautions should always be
followed, including the following:
DOs
a ) The user must weigh the tool or tools to be tethered
to ensure they do not exceed the maximum safe
working capacity of the tool lanyard or any part of
your tethering system. User should also refer to the
label or user manual for information on maximum
capacity information.
b ) Always inspect tool lanyard and all parts of the
tethering system prior to, and after each use (refer to
inspection steps).
c ) Use extra caution around moving machinery or
parts, electrical hazards, chemical hazards or other
apparent hazards.
d ) Always wear appropriate personal protective
equipment when installing or using tethering systems.
e ) Always ensure the carabiners are closed and locked
properly.
f ) Always ensure the hook & loop closure fasten
properly.
WARNING:
The user must weigh the tool to
be tethered to ensure they do not exceed the
maximum safe working capacity of the tool
lanyard or any part of the tethering system. User
should also refer to the label or user manual for
information on maximum capacity.
DON'Ts
a ) NEVER attach power tools to your body.
b ) Do not wrap tool lanyard around sharp or rough
edges.
c ) Never modify or alter power tool lanyard.
d ) Never modify a tool or primary anchoring location.
e ) Never tie a knot in a power tool lanyard.
f ) Never wrap the power tool lanyard back to itself,
unless specifically instructed.
g ) Do not connect more than one tool to each power
tool lanyard.
h ) Do not use this product if it interferes with the tool's
safe working condition, or the anchoring location -
including personal fall protection.
i ) Power tool lanyard must not be used as hoisting
taglines or used to statically suspend tools and
equipment.
j ) Never cinch the cord or carabiner around wrist.
k ) If not able to find a suitable connection point on the
tool, do not connect the lanyard.
English
WARNING:
Keep the power tool lanyard clean
and free of debris. Clean with a damp cloth and
mild soap, wipe of excess and thoroughly dry. Do
not use solvents.
INSPECTION
a ) A visual inspection is essential before using any
D
WALT equipment.
E
b ) Before each use, make sure you find no signs of cuts,
wear, discoloration, corrosion, etc. When in doubt, the
equipment should be replaced.
c ) Do not use this equipment beyond its weight limit.
d ) Always check the connection before each use.
e ) Power tool lanyard that has been used to arrest a
falling tool should be taken out of service.
f ) Always check the connection before each use.
MAINTENANCE AND CLEANING
a ) Proper care is important for maintaining the
safety and longevity of the tool tether. Before and
after each use, remove all dirt, corrosives, and other
contaminants from the D
WALT power tool lanyard.
E
b ) Do not wrap lanyard around sharp or rough edges.
c ) Power tool lanyard should not be used with blades,
knives, etc.
9
Publicidad
