Descargar Imprimir esta página

Intended Use; Assembly And Adjustments - DeWalt DWV106 Manual De Instrucciones

Publicidad

Idiomas disponibles

Idiomas disponibles

type designation. For example – SJTW-A to indicate it is
acceptable for outdoor use.
Minimum Gauge for Cord sets
Volts Total length of cord in feet (meters)
ampere
120V 25 (7.6) 50 (15.2) 100 (30.5) 150 (45.7)
rating
240V 50 (15.2) 100 (30.5) 200 (61.0) 300 (91.4)
Not
More
More
Than
Than
0
6
6
10
10
12
12
16
The label on your tool may include the following symbols. The
symbols and their definitions are as follows:
V ......................... volts
Hz ....................... hertz
min ..................... minutes
or DC ...... direct current
...................... Class I Construction
(grounded)
.../min .............. per minute
BPM .................... beats per minute
IPM ..................... impacts per minute
RPM .................... revolutions per
minute
sfpm ................... surface feet per
minute
SPM .................... strokes per minute
A ......................... amperes
W ........................ watts
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
COMPONENTS (FIG. A)

WARNING: Never modify the power tool or any part
of it. Damage or personal injury could result.
Refer to Figure A at the beginning of this manual for a
complete list of components.

INTENDED USE

This portable wet/dry vacuum DWV106 is designed for
professional applications.
Do NoT use under wet conditions or in presence of
flammable liquids or gases.
This portable wet/dry vacuum DWV106 is a professional
power tool. Do NoT let children come into contact with the
tool. Supervision is required when inexperienced operators
use this tool.

ASSEMBLY AND ADJUSTMENTS


WARNING: To reduce the risk of serious
personal injury, turn unit off before making any
adjustments or removing/installing attachments
AWG
18
16
16
18
16
14
16
16
14
14
12
Not Recommended
or AC ........... alternating current
or AC/DC .... alternating or
direct current
...................... Class II
Construction
(double insulated)
n
........................ no load speed
o
n ......................... rated speed
...................... earthing terminal
..................... safety alert symbol
..................... visible radiation
..................... wear respiratory
protection
..................... wear eye
protection
..................... wear hearing
protection
or accessories. An accidental start-up can
cause injury.
1. Pull lid latches in an outward motion, remove power
head and some accessories that may have been shipped
in the tank.
2. Attach heavy-duty rubberized casters following the
instructions in this manual.
3. Before replacing power head, refer to this manual to
ensure you have the proper filters installed for your
cleaning operation.
4. Replace power head, and apply pressure with thumb to
14
each latch until it snaps tightly in place. Make sure all lid
12
latches are clamped securely.
12
5. Insert the air hose end into inlet of tank.
6. Attach the extension wands to the accessory end of the
hose. Apply slight pressure until fitting is tight.
7. Attach one of the cleaning accessories (depending on
your cleaning requirements) on the extension wands.
Twist slightly to tighten the connection.
8. Plug the cord into the wall outlet. Your cleaniner is
ready for use.
CASTER ASSEMBLY (Fig. B)
1. Invert dust tank, take the caster to align the tank bottom
sinking place. Secure with screws provided.
2. Return dust tank assembly upright.
Fig. B

WARNING: To reduce the risk of fire or explosion, do
not operate this vac in areas with flammable gases,
vapors or explosive dust in the air. Flammable gases
or vapors include but are not limited to: lighter fluid,
solvent-type cleaners, oil-based paints, gasoline,
alcohol or aerosol sprays. Explosive dusts include
but are not limited to: coal, magnesium, aluminum,
and grain or gun powder. Do not vacuum explosive
dust, flammable or combustible liquids or hot ashes.
Do not use this vac as a sprayer for any flammable
or combustible liquid. To reduce the risk of health
hazards from vapors or dusts, do not vacuum toxic
materials.

WARNING: The operation of any utility vac can result
in foreign objects being blown into the eyes, which
can result in severe eye injury. Always wear safety
goggles complying with ANSI Z87.1 (or in Canada,
CSA Z94.3) before starting operation.

CAUTION: To reduce risk of hearing loss, wear ear
protectors when using the vac for extended hours or
when using it in a noisy area. The unit is ready for dry
vacuuming or blowing. After you plug the power cord
into the wall receptacle, turn the unit "ON" by pushing
ENGlIsh
21

Publicidad

loading