ROBLAN 227CBUCOPD17MOLF Manual De Instalación

227CBUCOPD17MOLF
IP66 Rated Compact Passive Infra Red (PIR)
Occupancy/Person Detector & Photocell
Input: 220-240 Vac 50Hz
PLEASE READ THESE INSTRUCTIONS BEFORE INSTALLING THE PRODUCT
NOTE: 227CBUCOPD17MOLF is only compatible to work with CASAMBI enabled equipment
This 227CBUCOPD17MOLF Lighting
Control has an IP66 rated
weatherproof enclosure and can be
surface mounted onto an external/
internal ceiling or wall. Confi gurable
via the free to download Casambi
APP on Google Play or Apple APP
Store.
INSTALLATION
To be installed by a competent person with
reference to BS 7671 or equivalent local standards.
If in doubt consult a qualifi ed electrician.
• Plan where the 227CBUCOPD17MOLF is to be located
(see diagrams 1 and 2). Switch off supply and
check for hidden cables and pipes.
• The detector should be sited so that it is not
shaded from daylight.
• Make sure the power is isolated from the circuit.
• Remove the front cover by by removing the two
screws on the front face of the product.
• The detector could be ceiling mounted up to
17 metres high, via any of the four pre-drilled
mounting holes only and must be mounted with
the cable entering from below.
• Thread mains cable carefully through the entry
point.
• The 227CBUCOPD17MOLF should be connected as
shown in diagram 3:
L - Live in. N - Neutral in.
• Replace the front cover ensuring the two screws
are secured.
OPERATION
To check the operation of the 227CBUCOPD17MOLF:
• Turn on the supply then after 20 seconds if the
sensor has recognised movement of a person
within its zone of detection.
The control also features adjustable time out (time
lag) control and daylight threshold control which
are confi gured by the Casambi APP.
PRECAUTIONS
• Do not place the 227CBUCOPD17MOLF near heat
sources, fans or in ventilated ceiling voids.
• Do not place close to, or positioned such
that, any light source points directly into the
227CBUCOPD17MOLF.
• Ensure wires and cables are securely held within
the connection terminals.
• The 227CBUCOPD17MOLF should be protected by
a 5 or 6 Ampere mcb or fuse.
• Disconnect the 227CBUCOPD17MOLF from the
circuit before performing insulation testing
of the wiring circuit.
ROBLAN EUROPA S.A.
Avda. de las Retamas 5. 45950
Casarrubios del Monte
Toledo, Spain
TECHNICAL DETAILS
INPUT
Voltage:
Frequency:
Max. mains current:
Standby current:
RADIO TRANSCEIVER
Operating frequencies:
Max. output power:
LUX PARAMETERS
Range:
OPERATING CONDITIONS
Note: The temperature difference between the
detection target and the background must be
at least 4 °C.
Ambient temperature:
Storage temperature:
Max. relative humidity:
CONNECTORS
Terminal block
Wire size:
Wire strip length:
Tightening torque:
MECHANICAL DATA
Dimensions:
Weight:
Degree of protection:
Protection class:
Material (casing)
Finish / Colour
Protection class:
CONFORMITY AND STANDARDS
EMC emission:
EMC immunity:
Safety:
Environment:
5 YEAR WARRANTY
227CBUCOPD17MOLF comes with a 5 year warranty
from the date of manufacture and is CE marked.
ROBLAN COLOMBIA S.A.S.
NIT. 900.748.926-0
ROBLAN AUSTRAL SPA
ROBLAN UK LTD
MANUAL DE INSTALACIÓN | INSTALLATION MANUAL
220 - 240Vac
50Hz
20mA
16mA
2.4... 2,483 GHz
+4 dBm
5 - 2000 lux
-20... +40 °C (lout
0.05 A)
-25... +75 °C
0... 80%, non cond.
0.5mm - 2.5mm
2 2
solid or stranded
6-7mm
0,4 Nm/4 Kgf.cm
75mm x 60mm x
37mm
100g (unpacked)
IP66
Built-in Class 2
Flame-retardant
polycarbonate/
Polypropylene.
Opaque /White (RAL
9003)
Built-in Class 2
EN60669-2-1:2004
inc. A12:2010
EN60669-2-1:2004
inc. A12:2010
EN60669-2-1:2004
inc. A12:2010
Complies with WEEE
and RoHS directives
www.roblan.com
Strong detection zone Secondary detection
i.e. person moving arm zone i.e. person walking
or walking towards PIR perpendicular to PIR
up to 20m
up to 24m
For optimum coverage recommended
mounting height: 17m
DIAGRAM 1 - CEILING MOUNTED DETECTION
Recommended
wall mounting
height 1 to 2.2
metres
Strong detection
zone (up to 10m)
DIAGRAM 2 - WALL MOUNTED DETECTION
Suggested typical wiring
N
230Vac
L
5A or 6A MCB
or fuse
L - Live in. N - Neutral in.
DIAGRAM 2
fron t
60
65
10
24
20mm threaded
entry spout
inside
4 x mounting
17 holes. 3M screws
recommended
(not supplied)
48
DIAGRAM 3 - DIMENSIONS IN MM
N
L
s ide
37