Highchair Assembly; Highchair Operation - Joie mimzy recline Manual De Instrucciones

Highchair Assembly

Please read all the instructions in this manual before assembling and using this product.
Assemble Support Leg
1. Assemble the front support leg to the front leg
secured to the Front Leg. 2
2. Assemble the rear support leg to the rear leg
to the rear leg. 4
Open Frame
1. Rotate rear leg back until an audible "click" is heard.
Assemble Seat
1. Open the seat. 6
2. Fit the seat onto the frame 7 . An audible "click" means the seat is secured to the frame.
!
Lift the seat up to be sure it is locked into place.
Assemble Seat Pad
Assemble the seat pad by following these steps:
1. Open the seat.
2. Insert the two seat pad anchor through openings in seat back.
!
Please make sure the seat pad anchor are secured to the seat back to prevent the seat pad from
slipping.
3. Pull all the harnesses through the slots in seat pad.
4. Wrap the seat pad over the top of seat back.

Highchair Operation

Adjust Calf Support
1. The calf support has 2 position settings.
2. Press the adjustment buttons on both sides of the seat
- 2
upward. 11
Adjust Footrest
1. The footrest can be adjusted to 3 positions.
2. To adjust the footrest, remove the footrest from the calf support
reinsert the footrest into the calf support. 13
11
1 . An audible "click" means the front support leg is
3 . An audible "click" means the rear support leg is secured
5
8
9
10
11 - 1
and rotate the calf support downward or
12 , choose a desired position, and then
Use Buckle
Note
1. To prevent serious injury or death from falling or sliding out, always secure child in the restraint.
2. Make sure the restraint harness is fitted correctly and the space between the harness and the
child does not exceed the thickness of an adult hand.
3. DO NOT cross the shoulder belts. This will cause pressure on child's neck.
Lock Buckle
Match the waist belt buckle up with the shoulder buckle and slide together
- 2
center buckle . A "click" means the buckle is locked completely
14
Release Buckle
Press the center button to release the buckles. 15
Adjust Height for Shoulder Harnesses
Note
1. The shoulder harness must go into the slot that is even with or slightly above the shoulders.
2. In order to protect your child from falling out, after your child is placed into the seat, check whether the
shoulder harnesses are at proper height.
3. For larger child, use the upper shoulder slots. For smaller child, use the lower shoulder slots.
1. Choose a pair of proper shoulder slots. Insert the shoulder harnesses into slots in seat pad and seat
back.
16 17
!
When changing shoulder harness slots, make sure shoulder harnesses are going through
same slots in seat pad and seat back.
Adjust Length for Harnesses
1. Use slide adjuster to change the harness length.
2. Pull waist harness to tighten to proper length
Use Tray
Assemble Tray
1. Fit the crotch restraint and tray mount onto the tray by pushing into the opening on the tray bottom until
you hear a "click" sound. 19 20
!
Both the crotch restraint and tray mount can only be assembled in one direction. The slots on the
crotch restraint and tray mount attachment should be aligned with the ribs in the opening of the tray
bottom.
2. Insert the tray guides into the holes in the seat, slide forward until a "click" is heard.
squeeze the button under the tray and slide off.
!
The tray horn must be inserted into tray before use. Once the tray horn is inserted, do not attempt
to remove it.
!
Use caution when adjusting tray, as the tray can be completely removed from the seat.
- 1
14 . Insert buckles into the
- 3
. Repeat for other side.
14
- 1
18
- 2
18
. Press the button to loosen the waist harness.
21 To remove tray,
22
- 3
18
12