Descargar Imprimir esta página

Publicidad

Enlaces rápidos

Manual
Cordless impact
screwdriver
Applies for:
Code
101606
DIMI-20A
CAUTION
Model
DIMI-20A
Read this manual thoroughly
before using the tool.
20 V
1/4"
Tip holder

Publicidad

loading

Resumen de contenidos para Truper DIMI-20A

  • Página 1 Manual Cordless impact screwdriver 20 V 1/4” Tip holder Applies for: Code Model 101606 DIMI-20A DIMI-20A Read this manual thoroughly CAUTION before using the tool.
  • Página 2: Tabla De Contenido

    Parts Start up Keep this manual for future references. Troubleshooting The illustrations in this manual are for reference only. They might be different from the real tool. Maintenance Environmental protection Notes Authorized service centers Warranty Policy DIMI-20A ENGLISH...
  • Página 3: Technical Data

    Technical Data DIMI-20A Code 101606 Description Cordless impact screwdriver Tip holder 1/4” Voltage 20 V Speed 0 - 2 600 RPM Strokes per minute 0 - 3 250 strokes per minute Rotation Forward – reverse Maximum torque 103 lb-ft (140 Nm)
  • Página 4: Safety Warnings For Power Tools

    Safety Warnings for Power Tools WARNING! Read carefully all safety warnings and instruction listed below. Failure to comply with any of these warnings may result in electric shock, fire and / or severe damage. Save all warnings and instructions for future references.
  • Página 5: Safety Warnings For Cordless Impact Screwdriver

    Safety Warnings for cordless impact screwdrivers Batteries and charger Choose the adequate accessory CAUTION • Take your time to evaluate the work to be done and • Use only screwdriver bits recommended make sure you have taken all the necessary precautions before you start drilling.
  • Página 6: Parts

    Parts Battery level Cross tip Tip holder indicator Tip holder collar light Direction of rotation locking button Handle Battery charger Switch Battery release button Battery connection prongs Charge Belt clip indicator Battery Start Up Battery charge 1. Plug the charger plug into a 127 V~ outlet (The green charging indicator light will turn on).
  • Página 7: Bit Installation

    Start Up Considerations for battery use The battery comes DISCHARGED from the factory. You will need to charge it for approximately 1 hour 30 minutes before you can use it. The normal charging temperature is 32 °F to 113 °F. Outside this range, charging is automatically suspended until the correct temperature is reached.
  • Página 8 Start Up Power on and operation control • Press the switch to start the operation. Release the switch to stop the operation. • The switch allows you to select the appropriate speed for each task. The harder you press the switch, the faster the tool will operate.
  • Página 9: Troubleshooting

    Troubleshooting Problem Cause Solution Tool loses efficiency. • Low battery. • Charge battery. Trigger cannot be • The direction of rotation knob is in the locked • Move the turn direction knob to the turn or pulled. position. reverse position. Trigger can be pulled •...
  • Página 10: Notes

    Notes ENGLISH...
  • Página 11: Authorized Service Centers

    Authorized Service Centers In the event of any problem contacting a Truper Authorized Service Center, please see our webpage www.truper.com to get an updated list, or call our toll-free numbers 800 690-6990 or 800 0187-8737 to get information about the nearest Service Center.
  • Página 12: Warranty Policy

    . Transportation costs resulting from compliance of this warranty will be covered by For questions or comments, call 800-690-6990. Made in China. Imported by Truper S.A. de C.V. Parque Industrial 1, Parque Industrial Jilotepec, Jilotepec, Edo. de Méx. C.P. 54257 Stamp of the business.

Este manual también es adecuado para:

101606