Publicidad
Idiomas disponibles
Idiomas disponibles
ENGLISH (Original Instructions)
Working with a straight guide (Fig. H)
The straight guide is effectively used for straight cuts
when chamfering or grooving.
Fit the straight guide (11) to the base (9) using the guide
screw (19).
Set the required stop depth using the wing bolt on the
straight guide (11).
While it is switched on, guide the power tool along the work-
piece edge with a uniform feed and while applying lateral
pressure to the parallel guide.
Edge or profile routing (Fig. I)
For edge and profile routing without a straight guide, the
router bit must be fitted with a pilot pin or a ball bearing.
While it is switched on, guide the power tool towards the
workpiece from the side until the pilot pin or the ball bearing
of the router bit is touching the side of the workpiece edge
that you want to machine.
Guide the power tool along the workpiece edge. Pay atten-
tion that the router is positioned perpendicularly. Too much
pressure can damage the edge of the workpiece.
Circular work (Fig. J)
Circular work may be accomplished if you assemble the
straight guide and guide plate as shown in the figure. Min.
and max. radius of circular to be cut (distance between the
center of circle and the center of bit) are as follows:
Min.: 65 mm
Max.: 222 mm
NOTE:
• Circles between 173 mm and 186 mm in radius cannot be
cut using this guide.
Align the center hole in the straight guide with the center of
the circle to be cut. Drive a nail less than 6 mm in diameter
into the center hole to secure the straight guide. Pivot the
tool around the nail in clockwise direction.
Router bits (Optional) (Fig. K)
No.
Description
1
Straight bit
2
Trimming bit
3
Rebating bit
4
V-grooving bit
5
Core box bit
6
Core bit
7
Ogee moulding bit Decorative edge moulding
8
Rounding over bit
9
Dovetail bit
24
Application
Grooves and rebates
Trimming laminates or
hardwood; accurate
profiling using a template
Rebates on straight or
curved workpieces
Grooves, engraving and
decorative edge moulding
Fluting, engraving and
decorative edge moulding
Decorative edge moulding
Rounding over edges
Dovetail joints
No.
Description
10
Chamfer bit
The shank diameter MUST correspond to the collet size
of the tool.
The bits diameter should be up to 26 mm.
MAINTENANCE
Your STANLEY tool has been designed to operate over
a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper
tool care and regular cleaning.
WARNING! To minimize the danger of serious
personal injury, please switch off the tool power
and disconnect all plugs before adjusting or
removing/ installing any accessory. Before
reassembling the tool, press and release the
trigger switch to make sure the tool is already
switched off.
WARNING! Before performing any maintenance
on corded/ cordless power tools:
Lubrication
Your power tool requires no additional lubrication.
Cleaning
WARNING! Blow dirt and dust out of the main
housing with dry air as often as dirt is seen
collecting in and around the air vents. Wear
approved eye protection and approved dust
mask when performing this procedure.
WARNING! Never use solvents or other harsh
chemicals for cleaning the non-metallic parts
of the tool. These chemicals may weaken the
materials used in these parts. Use a cloth
dampened only with water and mild soap. Never
let any liquid get inside the tool; never immerse
any part of the tool into a liquid.
ACCESSORIES
WARNING: Since accessories, other than those
offered by STANLEY, have not been tested with
this product, use of such accessories with this
tool could be hazardous. To reduce the risk of injury, only
STANLEY, recommended accessories should be used with
this product.
The performance of any power tool is dependent upon the
accessory used. STANLEY accessories are engineered to
high quality standards and are designed to enhance the
performance of power tool. By using STANLEY accessories
will ensure that you get the very best from your STANLEY
tool. STANLEY offers a large selection of accessories
available at our local dealer or authorized service center at
extra cost.
Application
Chamfer edges
Publicidad
