Go Green Total Power Meter Manual De Instrucciones

Total Power Meter
C
D
1,5 m
A
B
0,5 m
Mounting and replacing batteries
Remove the battery cover on the back of the receiver and place the included AAA batteries in the battery
compartment. Make sure polarity + and - of the batteries are same as market in the battery compartment.
Then replace the battery cover.
After placing the batteries all functions in de display will light up for a short moment.
When the batteries in the receiver are low on power, an indicator (a small battery ) will be shown in the display.
By using the hole for screws you can hang the meter any place you want or use the foldable feet on any flat surface.
Setting up the sensor
The Go Green Total Power Meter is only suitable for modern electronic meters with a pulse LED.
This is a small lamp indicating how much energy you are using. Normally these meters are set up to blink 1,000 - 10,000 times per
kilowatt hour (kwh).
Check the suitable mounting plate (C) or (D) before removing the adhesive tape.
It is important that the plate is mounted so that the LED diode of your meter is exactly in the middle of the
hole of the mounting plate.
Remove the adhesive tape and stick the mounting plate to your meter. Carefully place the sensor eye into place.
Turn the sensor eye clockwise until you will feel a "KLICK" and the sensor is locked on the mounting plate.
Connect the other part of the sensor eye to the cord of the Power Meter.
IMPORTANT
Avoid direct light on the sensor when in function. This may cause errors on the display.
SETTING
In order to set the Menu, press the Alarm On/Off / Menu button for 3 seconds.
Display Blinks Setting
12/24 hours Setting with the "+" and "-" buttons
Accept by pressing the SET / ALARM button
Hour Setting with the "+" and "-" buttons
Accept by pressing the SET / ALARM button
Minutes Setting with the "+" and "-" buttons
Accept by pressing the SET / ALARM button
Month/Day or Day/Month Setting with the "+" and "-" buttons
Accept by pressing the SET / ALARM button
Year Setting with the "+" and "-" buttons
Accept by pressing the SET / ALARM button
Day Setting with the "+" and "-" buttons
Accept by pressing the SET / ALARM button
Month Setting with the "+" and "-" buttons
Accept by pressing the SET / ALARM button
Introduction
The Go Green Total Power Meter helps you to limit
your electricity consumption and at the same time
reduce greenhouse gas emission.
It is important to understand that the Total Power
Meter is only a tool, the actual saving is up to you.
By keeping the values in the display as low as
possible you will save a lot of money on your
electricity bill as well as reduce the CO2 emission.
This set includes the following components:
A. Sensor head
B. Connection plugs / extension cord
C. Mounting plate flat
D. Mounting plate round
Imp (Impulses) Setting with the "+" and "-" buttons
Here you set how many impulses your electricity meter transmits
per kilowatt hour (kwh). This information is on your electricity meter.
Standard is 1,000 impulses/kWh,
Accept by pressing the SET / ALARM button
CO2 Set at 0.44 which is the standard for Europe
Setting with the "+" and "-" buttons.
Accept by pressing the SET / ALARM button
Electricity price per kWh Setting with the "+" and "-" buttons
Check your electricity bill to see what you pay per kWh inclusive
of taxes. Or call your electricity supplier and ask them.
Accept by pressing the SET / ALARM button
Setting Alarms
It is possible to set an alarm on your consumption, in that a way you have the possibility to pay attention to your consumption if it
is too high.
Press the "SET/ALARM" button. Select by the "HISTORY CLEAR MEM" button which period you want to set.
Select with the "COST, CO2, kWh" button whether you want the alarm on price, CO2 or kWh.
Select the value by pressing the "+" or the "-" button and confirm the digit by using the "SET/ALARM" button.
Example
I want an alarm, if I use more than 5 kW in one hour. Press the "SET/ALARM" button.
Select "hour" with the "HISTORY CLEAR MEM" button. Select "kWh" with the "COST,CO2,kWh" button.
Press the "SET/ALARM" button and key in 0005.00
The alarm is now programmed and can be activated by pressing "ALARM ON/OFF" at the top of the display unit.
A small bell will appear in the display indicating that the alarm is activated.
Rate setting
It is possible to set different prices at different times of the day. This is only relevant if you have different prices on your
consumption during the day.
Example:
From 06:00 – 18:00 your electricity price is 1.65
From 18:00 – 24:00 your electricity price is 1.75
From 24:00 – 06:00 your electricity price is 1.35
To set your rates press the "COST,CO2,kWh" button for 3 seconds.
At the top of the display it will say T1 standing for rate 1. Here you set the price by using the "+" and "-" buttons.
Press the "SET/ALARM" button to confirm and set the hours of the starting time of T1. Press the "SET/ALARM" button to
confirm and set the minutes of the starting time of T1. Repeat these steps to set price and time for T2 and T3.
It is possible to set maximum of 3 tariffs. The number of tariffs used will be shown in the display.
Display
The display shows real time information on top, history information in the middle and time and date in the bottom part.
By using the "COST,CO2,kWh" button you can switch between information on C02, cost and kWh.
By using the "HISTORY CLEAR MEM" button you can select information on hourly, daily, weekly and monthly base.
By using the "+" and "-" buttons you can select information in history. If you select daily information and press the
"-" button (- 1 is shown in the display), you get the information of 1 day ago.
Clear Memory
Push the "HISTORY CLEAR MEM" button for 3 seconds till you hear a signal. All history information is reset now.
SAFETY
This product is made to provide you with many years of satisfactory service if you treat it carefully. Here are
a few safety rules:
1. Do not immerse the unit in water.
2. Do not clean the unit with grinding or corrosive materials. This may result in scratches in the surface and attack
the electronic circuits.
3. Do not expose the unit to exaggerated impact, shaking, dust, temperature, or air humidity, as this may result in
malfunction, shorter electronic life, damaged batteries, and damaged parts.
4. Do not tamper with the internal components of the unit. This will make the warranty of the unit invalid and may result in
unnecessary damage. There are no parts in the unit which will require service on the part of the user.
5. Only use new batteries as described in the instruction manual. Do not mix new and old batteries, as the old batteries may leak.
6. Always read the instruction manual carefully before using the unit.
Technical data
Power : 2 x AAA 1,5 Volt batteries
Lifespan batteries : > 1 year
Art.nr. gsm00923
www.go-green.nl