Publicidad
Idiomas disponibles
Idiomas disponibles
PRECAUTIONS
Follow the advice below for safe and appropriate operations.
ON PLACEMENT
ON AC VOLTAGE
• Do not use the unit in places which
• Before use, check that the rated
are extremely hot, cold, dusty, or
voltage of your unit matches your
humid.
local voltage.
• Place the unit on a flat and even
surface.
ON CONDENSATION
• Do not restrict the air flow of the
• When left in a heated room where
unit by placing it in a place with
it is warm and damp, water
poor air flow, by covering it with a
droplets or condensation may
cloth, or by placing it on a carpet.
form inside the CD player.
• When there is condensation
ON SAFETY
inside the unit, the unit may not
• When
connecting
and
function normally.
disconnecting the AC cord, grip
• Let it stand for 1 to 2 hours before
the plug and not the cord itself.
turning the power on, or gradually
Pulling the cord may damage it
heat the room up and dry the unit
and create hazard.
before use.
• When you are not going to use the
unit for a long period of time,
disconnect the AC power cord.
FCC INFORMATION
This device complies with Part 15 of FCC Rules. Operations are subject to
the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference
that may cause undesirable operations.
Should any trouble occur, disconnect the AC power cord and refer
servicing to qualified personnel.
LISTENING TO THE RADIO
1.
Set the FUNCTION switch to
2.
Slide the BAND selector to
TUNER.
choose AM(MW) or FM.
3.
4.
Tune into the desired station.
Adjust the desired sound.
TUNING
FOR BETTER RECEPTION
AM(MW)
FM
Repositioning the unit to get better
Fully unwind the wire antenna. Then
extend the wire antenna and place
AM(MW) reception.
it in the position that sounds best.
NOTE: DO NOT CONNECT TO AN
OUTSIDE ANTENNA.
TO RECEIVE THE FM BROADCAST IN STEREO
Set the BAND selector to FM STEREO.
When the FM stereo broadcast is received, FM STEREO indicator lights up.
IF THE FM BROADCAST SIGNAL IS WEAK
Set the BAND selector to FM position to turn off the FM STEREO indicator
and background noises becomes mono.
AFTER LISTENING
Set the FUNCTION switch to TAPE/POWER OFF.
Get user manuals:
See SafeManuals.com
PARTS IDENTIFICATION
1. FM
STEREO/PROGRAM
indicator
2. POWER indicator
3. REMOTE SENSOR
4. CD PLAY/PAUSE indicator
5. FUNCTION selector
6. Cassette door
7. Cassette operation buttons
RECORD
PLAY
REWIND
F.FWD (Fast Forward)
STOP/EJECT
PAUSE
8. VOLUME control
9. PHONES jack
1 0 . CD door
1 1 . CD PLAY/PAUSE
1 2 . CD STOP
1 3 .
Forward Skip +
1 4 .
Reverse Skip -
1 5 . PROGRAM button
1 6 . BAND selector (AM/FM)
1 7 . TUNING control
1 8 . Dial scale
1 9 . AC cord
2 0 . FM antenna wire
2 1 . Speaker terminals
COMPACT DISC PLAYBACK
1.
Set the FUNCTION switch to
CD. "
display.
2.
Open the CD door. Place a
disc in the center with the label
side up and then close the CD
VOLUME
door gently. The total number
of tracks will show in the
display.
3.
Press the
up. Adjust the VOLUME.
TO INTERRUPT PLAYBACK
Press the
To resume playback, press the
TO STOP PLAYBACK
Press the STOP button.
button
button
'
" is shown in the
2
1
3
PLAY/PAUSE button. The PLAY/PAUSE indicator will light
PLAY/PAUSE button. The PLAY/PAUSE indicator will blink.
PLAY/PAUSE button again.
SYSTEM CONNECTIONS
IMPORTANT
Switch off the power before connecting speakers and other equipment.
SPEAKER CORD CONNECTION
Connect the wires with the printed
white lines to the red (+) terminals
and the plain-black wires to the
black (-) terminals.
Warning:
Connecting speakers other than
the speakers supplied with the
unit, may damage the unit.
USING HOUSE CURRENT
SPEAKER
Before use, check that the rated
voltage of your unit matches your
local voltage.
Caution: To prevent electrical
shock, match wide blade of
plug to wide slot, fully insert.
POWER INDICATOR
While the AC cord is connected:
• The POWER indicator will light up when the FUNCTION switch is set to CD
or TUNER.
• When the FUNCTION switch is set to TAPE/POWER OFF, the POWER
indicator will be switched off.
After using the unit, set the FUNCTION switch to TAPE/POWER OFF.
ADJUSTING THE SOUND
TO ADJUST THE VOLUME
Adjust the VOLUME control to obtain the desired volume level.
WHEN RECORDING
The VOLUME control may be adjusted with no effect on the recorded signal.
FOR PRIVATE LISTENING
Connect headphones (ø3.5mm stereo mini-plug) to the PHONES jack.
When the headphones is connected, speakers are automatically
disconnected.
COMPACT DISC PLAYBACK (continued)
TO SEARCH THROUGH TRACKS
• Search function is possible only in playback mode.
• Keep press either one of the (
buttons according to the desired direction, and
release at the desired point.
TO SKIP TO THE BEGINNING OF A TRACK
• Press either one of the (
/
) SKIP buttons
according to the desired direction, each press
skips one track.
• Playback resumes from the selected track.
COMPACT DISC PROGRAMMABLE PLAYBACK
1.
Press the PROGRAM button.
PROGRAM /
PROGRAM
2.
Press the
- SKIP +
buttons until the desired track
appears on the CD display.
OU
4.
Press steps 2 and 3 until all the
desired tracks are programmed
(up to 16 tracks).
NOTE :
Programming can only be done when the unit is in the stop mode.
SPEAKER TERMINALS
IMPEDANCE : 8 OHM (Ω)
RIGHT
LEFT
SPEAKER
BOX
BOX
1
2
AC cord to an
AC outlet
/
) SKIP
OU
Keep it pressed during play
OU
Each press skips one track
3.
Press the PROGRAM button.
PROGRAM /
PROGRAM
5.
Press the
PLAY / PAUSE
button.
Publicidad
