Oster Cordless Fast Feed Manual De Instrucciones página 5

CLEANING
USING THE ATTACHMENTS:
Plastic combs for attachment to clippers and trimmer blades are included with some kits. This plastic comb serves
as a clipping guide so that the hair is not clipped short. The comb attachment is grooved to fit snugly over the
blades.
When attaching the comb to the clipper or trimmer, slide the comb down firmly as far as it will go. Make sure the
comb is seated securely against the lower blade. To disengage the comb, pull and slide the comb upward until it is
off the clipper or trimmer.
Replacement combs are not covered under warranty.
BLADES
To clean the blades, fill a flat dish with Oster™ Blade Wash
NOT IMMERSE THE APPLIANCE. Turn «ON» (|) the appliance with the blades facing down. Do not hold the appliance
upright when cleaning blades with the appliance plugged in. Listen for a change in the hum of the motor. As the
build-up is removed, the clean blade runs faster and at a higher pitch. When the pitch stabilizes (between 30 to
60 seconds), turn «OFF» (O) the appliance and unplug. Remove from the cleaning solution and, while holding the
appliance with the blade end facing down, wipe the blades dry with a clean, dry cloth. Re-oil blades.
Always unplug the appliance when carrying out other cleaning and do not immerse the appliance body, charging
stand, adapter, power cord or plug in water or any other liquid.
CHARGING STATION
1. Disconnect the charging station from the power supply.
2. If necessary, remove hairs from both charging cavities.
3. If dirty, clean the contacts with a dry cloth.
CONTACTS
If required, clean the contacts of the trimmer and charging sand with a dry cloth.
Any maintenance beyond the cleaning and lubricating instructions in this manual should be performed by an
Oster™ Authorized Service Center.
The tasks described here for troubleshooting can be done mostly by the operator.
Some tasks only may be done by specially trained personnel or by an Oster
are marked with (*).
WARNING When using or cleaning this appliance, do not use any aerosol sprays or blade washes, especially
those containing methylene chloride, dimethyl benzyl ammonium chloride, or 1-1-1 trichloroethylene.
Damage caused by these chemicals will void your warranty. You may use Oster
washes, lubricants and disinfectant sprays that do not harm the product.
cleaning solution and immerse only the blade teeth. DO
®
authorized service center. These tasks
TM
approved blade
TM
8
English
The tasks described here for troubleshooting can be done mostly by the operator.
Some tasks only may be done by specially trained personnel or by an Oster
are marked with (*).
MALFUNCTION
Top blade does not move
Clipper cuts badly or not
at all
Motor is not running
Motor runs very slowly
Running time of a fully
charged battery is too
short and / or blades are
getting hot
When battery is unloaded
the light does not change
from green to red
TROUBLE SHOOTING
TM
CAUSE RECTIFICATION
Clipper-head is not well engaged Engage the clipper-head correctly when the
motor is running
Drive carrier is defective Replace drive carrier (*)
Clipper blade is blunt Have top and bottom blades re-sharpened by
Oster TM authorized service center
Clipper blades have not been
correctly grounded
Clipper blades are not oiled Oil clipper blades every 15 minutes
Hairs jammed between top and Take off clipper-head, push the top blade half
bottom blades away from the clipper head, take away hairs
between top and bottom blade
Clipper-head has too little clipping Have clipper-head inspected (*)
pressure
Battery is not charged Charge battery
Contacts dirty Switch clipper «OFF» (O) and clean the contacts
Faulty battery Replace battery (*)
Smell of burning from the motor Have motor and / or electronics replaced (*)
housing. Motor burned out
Motor and / or electronics faulty Have motor and / or electronics replaced (*)
Clipper-head blocked Clean and oil clipper-head
Clipper blades were not oiled Oil clipper blades
sufficiently
Clipper blades were not oiled Oil clipper blades
sufficiently
Battery is not fully charged, or faulty Only use intact, fully charged original batteries
battery is being used
Contacts dirty Clean contacts
Faulty battery Replace battery (*)
Contacts of the charging station are Have the charging station repaired (*)
deformed
9
English
authorized service center. These tasks