Remote Control; Mode Button - Sharp UL-C10EA-W Manual Del Usuario

6
Operation of Control Panel
ON/OFF button
Pressing this button turns the air conditioner on and off.
+ / - button
Under cooling or heating mode, press "+" or "-" button to increase or
decrease set temperature by 1°C . Set temperature range is 16°C to 30°C.
When in the auto, dry or fan mode, these buttons will not operate.
Fan button
Press this button and the fan speed will change as:
low speed >> medium speed >> high speed >> auto fan

Mode button

Press this button and the mode will change as:
COOL >> DRY >> FAN >> HEAT (Cool and Heat model only)
COOL: Under this mode, cool mode indicator will be on.
Display panel displays set temperature.
Temperature setting range is 16°C ~ 30°C.
DRY: Under this mode, dry mode indicator will be on.
Display panel won't display.
FAN: Under this mode, only the fan will work. Fan mode indicator will go
on. Display panel won't display.
HEAT (Cool and Heat model only): Under this mode, heating mode
indicator will go on. Display panel displays set temperature. Temperature
setting range is 16°C ~ 30°C.
Timer button
When setting the timer in the off mode, it will work as an ON timer
function. When setting the timer in the on mode, the timer will work as an
OFF timer. Note that the ON timer and OFF timer cannot be set together.
Press the timer button to enter the timer set mode. When in the timer
mode, use the – and + buttons to select the time in 0.5 intervals. When
the display shows 10 hours, the + and - buttons will set in 1 hour intervals.
After setting duration time, press timer button again to confirm the setting.
When ON timer is set, the unit will start operating when the time set has
elapsed. When OFF timer is set, after setting the timer, the timer display
will be replaced with the temperature after five seconds.
To cancel the timer, press the timer button again.
Swing
Press this button, horizontal louver of air conditioner will swing up and
down automatically. Single press it to switchover between on and off.

Remote control

Remote control buttons
Refer to the pictures 4 on page 1.
1. ON/OFF
2. MODE
3. +/-
4. FAN
5. SWING
6. SLEEP
7. TIMER
Remote control display
Refer to the pictures 5 on page 1.
1. AUTO – Auto mode
2. COOL – Cool mode
3. DRY – Dry mode
4. FAN – Fan mode
5. HEAT – Heat mode (Cool and Heat models only)
6. T-ON – Timer on
7. T-OFF – Timer off
8. SWING – Swing operation
9. SLEEP – Sleep operation
10. LOCK – Lock
11. SPEED – Set fan speed
12. Set temperature
13. Set time
14. Send signal
Remote control functions
NOTE:
ū The remote control may have more functionality than your air
conditioner has. If any additional buttons are pressed, they will have no
affect on the operation of the unit.
ū When power is connected (stand by condition), you can operate the air
conditioner through the remote control.
ū When unit is on, each time you press the button on remote control, the
signal icon " " on the display of remote control will blink once. If the
air conditioner emits a sound, it means the signal has been sent.
ū When unit is off, set temperature will be displayed on the remote control
(If the light of indoor unit display is turned on, the corresponding icon
will be displayed). When unit is on, the icons of the ongoing functions
will be displayed on the remote control.
ON/OFF button
Press this button to turn unit ON/OFF.
MODE button
Pressing this button once can select your required mode as shown below.
(the corresponding icon " " will be lit up after the mode is selected):
AUTO >> COOL >> DRY >> FAN >> HEAT (Cool and Heat model only)
• When selecting AUTO, air conditioner will operate automatically
according to ambient temperature. Set temperature can't be adjusted
and won't be displayed either. Press FAN button to adjust fan speed.
• When selecting COOL, air conditioner will operate under cooling mode.
Then press + or - button to adjust set temperature. Press FAN button to
adjust fan speed.
• When selecting DRY, air conditioner will operate at low fan speed under
dry mode. In dry mode, fan speed can't be adjusted.
• When selecting FAN, air conditioner will operate in fan mode only. Then
press FAN button to adjust fan speed.
• When selecting HEAT, air conditioner will operate under heating mode.
Then press + or - button to adjust set temperature. Press FAN button to
adjust fan speed. (Cooling only unit can't receive heating mode signal. If