Additional Safety Warnings - HIKOKI C 3606DPA Instrucciones De Manejo

English
f) Blade depth and bevel adjusting locking levers
must be tight and secure before making the cut.
If blade adjustment shifts while cutting, it may cause
binding and kickback.
g) Use extra caution when sawing into existing walls
or other blind areas.
The protruding blade may cut objects that can cause
kickback.
Guard function
a) Check the guard for proper closing before each
use. Do not operate the saw if the guard does not
move freely and enclose the blade instantly. Never
clamp or tie the guard so that the blade is exposed.
If the saw is accidentally dropped, the guard may be
bent. Check to make sure that the guard moves freely
and does not touch the blade or any other part, in all
angles and depths of cut.
b) Check the operation and condition of the guard
return spring. If the guard and the spring are not
operating properly, they must be serviced before
use. The guard may operate sluggishly due to damaged
parts, gummy deposits,or a build-up of debris.
c) Assure that the base plate of the saw will not shift
while performing a "plunge cut". Blade shifting
sideways will cause binding and likely kick back.
d) Always observe that the guard is covering the blade
before placing the saw down on bench or fl oor. An
unprotected, coasting blade will cause the saw to walk
backwards, cutting whatever is in its path. Be aware
of the time it takes for the blade to stop after switch is
released.

ADDITIONAL SAFETY WARNINGS

1. WARNING: It is important to support the work piece
properly and to hold the saw fi rmly to prevent loss
of control which could cause personal injury. Fig. 2
illustrates typical hand support of the saw.
2. Avoid cutting in the state where the base has fl oated up
from the material.
When blade is binding, or when interrupting a cut for any
reason, release the trigger and hold the saw motionless
in the material until the blade comes to a complete
stop. Never attempt to remove the saw from the work
or pull the saw backward while the blade is in motion or
KICKBACK may occur. Investigate and take corrective
actions to eliminate the cause of blade binding.
3. Support large panels to minimize the risk of blade
pinching and KICKBACK. Large panels tend to sag
under their own weight (Fig. 3-b). Supports must be
placed under the panel on both sides, near the line of cut
and near the edge of the panel as shown in Fig. 3-a.
To minimize the risk of blade pinching and kickback.
When cutting operation requires the resting of the saw
on the work piece, the saw shall be rested on the larger
portion and the smaller piece cut off .
4. The protruding blade may cut objects that can cause
KICKBACK.
NEVER place your hand or fi ngers behind the saw
(Fig. 4). If kickback occurs, the saw could easily jump
backwards over your hand, possibly causing severe
injury.
5. Place the wider portion of the saw base on that part of the
work piece which is solidly supported, not on the section
that will fall off when the cut is made. As examples,
Fig. 5-a illustrates the RIGHT way to cut off the end of
board, and Fig. 5-b the WRONG way. If the work piece
is short or small, clamp is down.
DON'T TRY TO HOLD SHORT PLACES BY HAND!
6. When using the guide, do not attempt an inclined cut
which would allow the cut material to slip between the
saw blade and guide. Doing so could result in injury.
(Fig. 6)
7. Wear earplugs to protect your ears during operation.
8. Use only blade diameter specifi ed on the machine.
9. Do not use any abrasive wheel.
10. Do not use saw blades which are deformed or cracked.
11. Do not use saw blades made of high speed steel.
12. Do not use saw blades which do not comply with the
characteristics specifi ed in these instructions.
13. Do not stop the saw blades by lateral pressure on the
disc.
14. Always keep the saw blades sharp.
15. Ensure that the retraction mechanism of the guard
system operates correctly.
16. Never operate the plunge cut saw with the saw blade
turned upward or to the side.
17. Ensure that the material is free of foreign matters such as
nails.
18. Pull out battery before carrying out any adjustment,
servicing or maintenance.
19. Be careful of brake kickback.
This power tool features an electric brake that functions
when the switch is released. As there is some kickback
when the brake functions, be sure to hold the main body
securely.
20. Ensure that the switch is in the OFF position. If the battery
installed to power tool while the switch is in the ON
position, the power tool will start operating immediately,
which could cause a serious accident.
21. Never use a power tool with its locking screws or
clamping lever loosened or with its lock lever lowered.
After making adjustments, be sure to return the lock
lever and other parts to their original positions.
22. Prior to cutting operation, make sure the material you
are going to cut. If the material to be cut is expected to
generate harmful / toxic dusts, make sure the dust bag
or appropriate dust extraction system is connected with
dust outlet tightly.
Wear the dust mask additionally, if available.
○ Before starting to saw, confi rm that the saw blade
has attained full-speed revolution.
○ Should the saw blade stop or make an abnormal
noise while operating, promptly turn OFF the switch.
○ Using the plunge cut saw with the saw blade facing
upwards or sideways is very hazardous. Such
uncommon applications should be avoided.
○ When cutting materials, always wear protective
glasses.
○ When fi nished with a job, pull out the battery.
23. Use a saw blade with a displayed speed that is equal to
or higher than the rotation speed displayed on the tool.
24. Always use the tool and battery at temperatures between
-5°C and 40°C.
25. If you notice that the unit is generating unusually high
temperatures, operating poorly, or making abnormal
noises, immediately stop using and shut off the power
switch. Request an inspection and repair from the dealer
where you purchased the unit or a HiKOKI Authorized
Service Center.
Continuing to use while operating abnormally might
cause injuries.
26. If the unit is mistakenly dropped or strikes another object,
make a thorough check of the unit for cracks, breakage
or deformation, etc.
Injuries might occur if the unit has cracks, breakage or
deformation.
27. When working at elevated locations, clear the area of
other people and aware of conditions below you.
10